User Account

All Pages

What is the output impedance of the amplifier

Assignment Help Electrical Engineering
Reference no: EM13229614

Suppose that without a 1k-ohm load an amplifier's output voltage is 5Vpp but when the 1k-ohm load is attached, it drops to 3Vpp. What is the output impedance of the amplifier?

Reference no: EM13229614

Questions Cloud

Determine the power loss due to the line impedance : A balanceed three-phase load of 15 MA with a lagging load factor of 0.85 is supplied by a 115KV subtransmission line. if the line impedance is 50+j100Ohm per phase, determine the following: (a) The line current of the load
Find the line-to-line voltage of the line at the sending end : A balanceed three-phase load of 15 MA with a lagging load factor of 0.85 is supplied by a 115KV subtransmission line. if the line impedance is 50+j100Ohm per phase, determine the following: (a) The line current of the load.
Explain neutralize more moles of hydronium ion : will 500 mg of Na3C6H5O7 (258.1g/mol) or 500 mg of CaCO3 (100.1g/mol) neutralize more moles of hydronium ion? Assume that both the C6H5O7^(3-) and CO3^(2-) ions become fully protonated.
Determine the current in the neutral wire : A three-phase, wye-connected induction motor is supplied by a three-phase and foursin system with line-to-line voltage of 220V and the impedance of the motor is 6.3+j3.05Ohm per phase.
What is the output impedance of the amplifier : Suppose that without a 1k-ohm load an amplifier's output voltage is 5Vpp but when the 1k-ohm load is attached, it drops to 3Vpp. What is the output impedance of the amplifier
Explain what is the ph of a solution in methylamine : What is the pH of a solution that is 0.125 M in methylamine (CH3NH2) and 0.175 M in methylamine chloride (CH3NH3Cl)?
What volume of red dye is needed to reach the endpoint : A 4.16 g sample of ascorbic acid is titrated with 0.83 M red dye. What volume of red dye is required to reach the endpoint? Molar mass of red dye =267.08 g/mol; molar mass of ascorbic acid =176.12 g/mol
What is the resistance at the boiling point of water : 1. a nichrome wire 12 ft long and .011 inch diameter conducts 1.83A when 120v are applied. what is the resistivity of nichrome 2. Copper windings of an electric motor at room temperature of 25 degrees C has resistance of .20(r).
Compute the concentrations of h+ : calculate the concentrations of h+, oh-, f-, and undissociated hf molecules in 0.10 M hf. Ka for HF is 7.1x10^(-4).

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Implement a multiple mode counter

Implement a multiple mode counter

  Design an op-amp amplifier circuit

Design an op-amp amplifier circuit where the smallest resistor available is 10k . The circuit must yield the relationships shown in the following equation: Vout = 8v1 + 8v2 - 4va - 9vb

  When is the binary input value in decimal

Design a combinational circuit with four inputs, x,y,w, and z, and four outputs: A, B, C, and D. When the binary input value in decimal is 3,5,6,9,10 or 12, the binary output value is one less than the input value, otherwise it is one greater than..

  Find the time when capacitor voltage reads vc

A 3.0 microFarad capacitor is connected in series to 100kohms resistor, a toggle switch, and a 24 V DC power supply. Determine I (t=Tow) and Vr (t=Tow), Vc (t=Tow). Determine I(t=2Tow, Vr(t=2Tow, and Vc(t=2Tow).

  Find the normal force exerted by the pavement on the tires

A curve of radius 159 m is banked at an angle of 11°. An 810-kg car negotiates the curve at 93 km/h without skidding. Neglect the effects of air drag and rolling friction. Find the normal force exerted by the pavement on the tires.

  Implementation of the project:

Implementation of the project with the analog and digital modulation techniques

  What is initial value if the overhead values were considered

write an 8051 program that would generate a 200khz, 50% duty cycle, square wave at P1.0.Use Timer 0 for the delay. Ignore the overheads cycles due to the instructions in the loop. Assume 12 MHz clock. All data must be hex.

  Discuss the procedure for design using anthropometric data

Discuss the procedure for design using anthropometric data. Include Confidence Intervals (CIs). Select any one anthropometric measurement for males or females in Table 5.3 and find 90% CI for the mean measurement of the population.

  Find the maximum acceleration that can be measured

An LVDT (Linear Variable Differential Transformer) is used in an accelerometer to measure seismic-mass displacement. The LVDT and signal-conditioning output is 0.31 mV/mm with a +/- 2 cm maximum core displacement.

  Realize the storage circuits for n1 and n2

Realize the storage circuits for N1 and N2 as describe in the design specification.

  Explain vary as square root-application

Vary as square root-application, The frequency f of vibration of a wire varies directly as the square root of the tension T of the wire

  Calculate the equivalent impedance for three parallel loads

Three loads are connected in parallel across a single-phase source voltage of 240 V (RMS). Load 1 absorbs 12 kW and 6.667 kVAR; Load 2 absorbs 4 kVA at 0.96PF leading; Load 3 absorbs 15 kW at unity power factor.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd