What is the order of the system

Assignment Help Mechanical Engineering
Reference no: EM131200232

The circuit shown in Figure P3.21 has an inductor L, a capacitor C, a resistor R, and a voltage source v(t). Considering that L is analogous to a spring, and C is analogous to an inertia, follow the standard steps to obtain the state equations. First sketch the linear graph denoting the currents through and the voltages across the elements L, C, and R by (fl , vl ), (f2, v2) and (f3, v3), respectively, and then proceed in the usual manner

(i) What is the system matrix and what is the input distribution matrix for your choice of state variables?

(ii) What is the order of the system?

(iii) Briefl y explain what happens if the voltage source v(t) is replaced by a current source i(t).

FIGURE P3.21

2047_bcbe7bbe-7a36-4c36-a294-b78d8a9e2afe.png

Reference no: EM131200232

Questions Cloud

National infrastructure protection mission : Which U.S. federal agency has taken control of the overall National Infrastructure Protection mission?
More women have become primary wage earners in households : Over time, more women have become the primary (or sole) wage earners in their households.  - How does this fact complicate the empirical analysis of the effects of taxation on women's labor supply?
Demonstrate understanding of the topics : The key to this assignment is to demonstrate your understanding of the topics, not to re-word the text or reference material. Please see Appendix A for the grading rubric on all written assignments.
Will the increase number of people hired why or why not : Will this increase the number of people entering this labor market? Why or why not? Will this increase the number of people hired? Why or why not?
What is the order of the system : What is the system matrix and what is the input distribution matrix for your choice of state variables?
Draw an isosceles triangle : Using the Point and Line classes described in Section 7.2, see page 78 of attachment draw an isosceles triangle with the following configuration:start = Point(1, 1)finish = Point(4, 5)l = Line(start, finish)l.draw(win)a triangle inthe graphics win..
What happen to labor supply eitc compensation rate increase : What is likely to happen to overall labor supply if  the EITC compensation rate increases from 30% to 50% for each dollar earned?
Define similarities and differences of the her code sets : Describe the similarities and differences of the HER code sets. In no more than one paragraph discuss why an HER code set has to provide equilibrium between granularity and point of care requirements.
System of simultaneous equation and graph the results : Solve the following system of simultaneous equation and graph the results. Y = 50 +2x (1) Y = 100 -0.5x (2). Assume that the intercept of equation 1 from problem 4 has increase by 5 units. Graph the new and old equations. Assume that the slope of equ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd