Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
To avoid the salinization of soil in a farming area, parallel drainage canals are to be installed to maintain the water table at a depth of at least 4m below the ground surface. It is thought that no evapo-transpiration would occur below that depth. This water table aquifer has hydraulic conductivity of 1.5 m/day. The canals fully penetrate the aquifer and have a stage of 3m. The design depth from the ground surface to the bottom of the canal is 10 m. The daily recharge from precipitation and irrigation to the aquifer is 0.019 m.
a)What is the optimal distance between the two drainage canals to achieve the desired water table control?
b)What is the discharge rate per unit width of the aquifer to the canals?
A 2-ft diameter circular pipe has a Manning's n of 0.013 and a bed slope of 2.0 X 10^-3. What is the uniform flow rate in this pipe if it is completely full (Qf) in ft^3/s
estimate the theoretical production of landfill gas (CH4 only) from the degradation of 20.3 kg of rapidly decomposable MSW. asssume the density of methane is 0.7177 kg/m^3.
The thickness of geonet is 0.2 inch (5 mm). Assume the maximum inflow rate is 0.14 inch/hour. The liquid head over the geomembrane liner is 2 inches. The index properties of the soil placed over the geotextile are as follows
for what flowrate through the Venturi meter will cavitation begin if p1=275 kPa gage, atmospheric pressure is 101 kPa (abs) and the vapor pressure is 3,6 kPa (abs)
For each subcritcal, critcal, and supercritcal flows, comment on the values for the Froude number, the depth of the water channel, and the specific energy. How do these values compare to each other for each of the flow types
(a) Determine the desired diameter of the disk. (b) If the rubber strain is not to exceed 0.2 in/in, determine the maximum allowable compressive force. Recall that the spring constant, k=Fx,or in terms of an axially loaded member
Water at a flow rate of 1 kg/s is flowing in a pipe of internal diameter 5 cm. If the inside pipe surface temperature is 90 degrees C and mean bulk water temperature is 50 degrees C
Two materials A and B are tested and a stress-strain curve is plotted. Material B has a yield stress of 200 MPa and Material A has a Yield stress of 120 MPa. These materials have plastic Deformation occur at the same Yield strain %.
the pressure inside a commercial airliner is maintained at 1.00 ATM. what is the net upward force exerted on a (1.0 m)(200 cm) cabin door if the outside pressure is 0.30 ATM?
A water storage tank is on the roof of a factory building & the surface of the water is 50 ft above the floor of the factory. if a pipe connects the storage tank to the floor level & the pipe is full of static water
Biological treatment processes for wastewater can be catogarised as dispersed growth and attached growth systems. Discuss the advantages and disadvantages of attached growth systems over dispersed growth systems.
a cylinder has 500 cm3 of water. after a mass of 100 grams of sand is poured into the cylinder and all air bubbles are removoed by a vacuum pump, the water level rises to 537.5 cm3. Dteremine the specific gravity on the sand
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd