What is the net rate of work output

Assignment Help Mechanical Engineering
Reference no: EM13702414

The ideal regenerative Rankine cycle for a power plant (shown below), where there is no heat loss or pressure drops in the piping, the turbine and pumps are isentropic, the heat loss in open feed water heater (FWH) can be neglected, there are no pressure drops in the boiler, condenser, and FWH, and the steam leaves the condenser and FWH as saturated liquid.

a) Sketch the T vs. s cycle/diagram for this non-ideal Rankine power plant (including the T vs. s bell-curve for water/steam and the exact values of T & s at each stage).

b) Sketch the P vs. v cycle/diagram for this ideal Rankine power plant (including the P vs. v bell-curve for water/steam and the exact values of P & v at each stage).

c) What is Mass flow rate at stages 6 & 7?

d) How much heat input (to the boiler) is needed in 10 seconds?

e) What is the net rate of work output?

Reference no: EM13702414

Questions Cloud

Role of signal processing in an engineering application : What could the contaminant/toxicant/pollutant be and where could the contaminant have likely come from -  explain how all the information provided in the case study backs up your Diagnosis.
How far up the ramp will the spring send the crate : A crate of mass 10kg is placed on a ramp elevated at 30 degrees from the horizontal. The ramp is 2m long. The coefficient of static friction is .4 and coefficient of kinetic friction is .3. At the low end of the ramp and oriented parallel to it is a ..
What is the speed of the truck after impact : A car weighing 5000 lb traveling at 60mph strikes the rear of a 20,000 truck that is stopped but does not have its brakes set. A.) Both vehicles stick together and move in the same direction as the car. At what speed are they moving? B.) The do not s..
Poly tropic coefficient and associated boundary work : A closed system contains 0.5 kg of nitrogen, initially at 150 KPa with a volume of 0.3 m^3. The system undergoes a poly tropic process resulting in the final state of 240 KPa and 100 C. Determine a) the poly tropic coefficient and b) the associated b..
What is the net rate of work output : The ideal regenerative Rankine cycle for a power plant (shown below), where there is no heat loss or pressure drops in the piping, the turbine and pumps are isentropic, the heat loss in open feed water heater (FWH) can be neglected, there are no pres..
Calculate the volumes corresponding to all three states : A vertical piston- cylinder assembly contains 0.6 kg of air (K=1.4, R= 287J/Kg.K) initially at 110 KPa and 27 C (state 1). The air is first compressed isentropic ally to a temperature of 117 C ( state 2) which is followed by a constant pressure expan..
The poly tropic coefficient and associated boundary work : A closed system contains 0.5 kg of nitrogen, initially at 150 KPa with a volume of 0.3 m^3. The system undergoes a poly tropic process resulting in the final state of 240 KPa and 100 C. Determine a) the poly tropic coefficient and b) the associated b..
Water cools at a rate : Water cools at a rate of 0.1 deg C per second as it flows in a pipe at 1 m / s. At any fixed location, the temperature is independent of time. If the pipe is 10 m long, what must the temperature be at the upstream end to keep the water temperature at..
The women dives first and the man dives first : A 90-kg man and 60-kg woman stand side by side at the same end of of 150-kg boat ready to dive, each with a 5-m/s velocity of the boat after they have both dived, if (a) the women dives first, (b) the man dives first.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd