What is the molar concentration of the complex in a solution

Assignment Help Mechanical Engineering
Reference no: EM131083702

A solution containing the complex formed between Bi(III) and thiourea has a molar absorptivity of9.32 X 103 L mol-1 cm-1 at470 nm.

(a) What is the absorbance of a 3.79 x 10-5 M solution of the complex at 470 nm in a 1.00-cm cell?

(b) What is the percent transmittance of the solution described in (a)?

(c) What is the molar concentration of the complex in a solution that has the absorbance described in (a) when measured at 470 nm in a 2.50-cm cell?

Reference no: EM131083702

Questions Cloud

Describe the board of governors : Describe the Board of Governors. Be sure to include the number of years that they serve and the importance of appointing them for that number of years, how many members are on the board.
Basis of present worth analysis at interest rate : Three different plans were presented to the US GAO (Government Accountability Office) by a high-technology facilities manager for operating a small weapons production facilities. Assuming that GAO could renew any of the plans under the same condition..
Earnings for carlson cargo : The earnings for Carlson Cargo, have been predicted for the next five years and are listed below.  There are 1 million shares outstanding.  Determine the yearly dividend per share to be paid if the following policies are enacted:
What is the molar concentration of the complex in a solution : What is the molar concentration of the complex in a solution that has the absorbance described in (a) when measured at 470 nm in a 2.50-cm cell?
Discuss the assumptions used to assign weights : Discuss the assumptions used to assign weights to each variable of your sensitivity analysis - That is, provide the rationale for your choice of weights for each variable.
Part of the rehabilitation of the downtown area : As part of the rehabilitation of the downtown area of a southern U.S. city, the Parks and Recreation Department is planning to develop the space below several overpasses into basketball, handball, miniature golf, and tennis courts. The initial cost i..
Inspection of the code for poisson arrivals : Recall that for a rate λ Poisson process, the expected number of arrivals in [0, T ] is λT. Inspection of the code for poissonarrivals(lambda,T)will show that initially n = [1.1λT] arrivals are generated. If Sn > T , the program stops and returns ..
Hot-patch short section of existing county road or resurface : A state highway department is trying to decide whether it should “hot-patch” a short section of an existing county road or resurface it. If the hot-patch method is used, approximately 300 cubic meters of material would be required at a cost of $700 p..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd