What is the minimum spacing of the tones

Assignment Help Electrical Engineering
Reference no: EM131206824

Approximate the power spectrum of coherent M-ary FSK by adding voltage spectra of sinusoidal bursts of duration Tb and of the appropriate frequency coherently, and then plotting the magnitude squared. What is the minimum spacing of the ‘‘tones'' in order to maintain them coherently orthogonal?

Reference no: EM131206824

Questions Cloud

Find the period of a periodic waveform : Find the period of a periodic waveform whose frequency is  25 Hz, 35 MHz, 55 kHz, and  1 Hz.
Discuss how the statements align with the selected method : Discuss how these statements align with the selected method. Look for recommendations for future research in these articles. Discuss what you found and if what you found could serve as the foundation for a future research paper.
Guidelines proposed by one other organization : Compare the CMS standards with the guidelines proposed by one other organization. Based on this comparison, would you recommend that a health care setting adopt this organization's guidelines as supplementary to CMS's?
Describe and analyse the different procurement methods : School of Computing, Engineering and Mathematics - 300053 Professional Practice - describe and analyse the positive and negative aspects of three different procurement methods for construction projects.
What is the minimum spacing of the tones : What is the minimum spacing of the ‘‘tones'' in order to maintain them coherently orthogonal?
Problem regarding the criteria of decision-making : Dale, a manager, is assessing possible alternatives for the solution of a quality problem in his department. As Dale does so, he attempts to determine if a possible alternative will threaten other company projects. Which of the following criteria ..
Find the frequency of a repeating waveform : Find the frequency of a repeating waveform whose period is - 1/60 s,  0.01 s,  34 ms, and  25 ms.
Determine the antenna aperture diameter : Given a satellite altitude and desired illumination spot diameter on the earth surface, use MATLAB to determine the antenna aperture diameter and maximum gain to give the desired spot diameter.
Calculate the required rate of return for given ten stocks : Then, use the following workbook to calculate the required rate of return for those ten stocks. Are you surprised by the required rate of return? Why or why not?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the zener voltage at a current

a 9.1 v zener diode exhibits its nominal voltage at a test current of 28 mA . at this current the incremental resistance is specified as 5 ohms . find Vz0 of the zener model . find the zener voltage at a current of 10 mA and at 100 mA.

  Find the rrns voltage across the capacitor.

Find the time averaged output power of the generator in this circuit.

  Determine the impulse response for the system

noncausal, linear, and time-invariant. Determine the impulse response for the system and verify that an LTI system defined by the impulse response you determined satisfies the difference equation.

  Calculate resistance from measured voltage and current value

Calculate resistance from the measured voltage and current values. Measure the resistance for the resistor in the circuit. Compare the measured resistance to the calculated value of resistance of the resistor.

  Calculate the value of q for the filter

Design a band-pass filter with a low cutoff frequency of 200 Hz, a high cutoff frequency of 1 kHz, and a pass-band gain of 4. Calculate the value of Q for the filter. Also, draw the approximate frequency response of this filter.

  What is the voltage difference between the two plates

Two large flat charged plates are fixed parallel to one another in a large tank of distilled water (Er=81) with a total surface charge of 41.25×10-7 C on each plate (with opposite polarities). The plates are square, 4 m each side.

  Potential difference between the plates

How do you take into account the potential difference between the plates?

  Determine the location of the shear center o

Determine the location of the shear center O of a thin-walled beam of uniform thickness having the cross section shown.

  Find the new bit error rate in the presence of the jammer

It is decided to apply a Fast Hopping (FH) scheme on the above ASK system. The hopping is made over 12 channels of 100 kHz; or over 1.2 MHz bandwidth. The ASK signal hops 6 bands per bit period. Now a strong jammer randomly jams one of the 12 FH c..

  Determine the compensator pole of utility feedback system

A unity feedback control systems for a robot submarine has a plant with a third-order transfer function G(s) = K / (s(s + 10)(s +50)) We want the overshoot to be approximately 7.5% for a step input

  How many standard ttl gates can this gate drive

A LSTTL gate has an IOL = 8 mA. How many standard TTL gates can this gate drive. The standard TTL gate has IIL = -1.6 mA

  Calculate the value of c to achieve this condition

It is desired to run the motor in the previous problem with a power factor of unity. To achieve this, a capacitor C is connected in parallel across the motor, which results in a circuit like that shown in Fig. 2.13. Calculate the value of C to ach..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd