User Account

All Pages

What is the minimum sampling rate that can be used

Assignment Help Electrical Engineering
Reference no: EM13265438

What is the minimum sampling rate that can be used to obtain samples that completely specify the following signal
x(t) = 10cos(20*pi*t) - 5cos(100*pi*t) + 20cos(400*pi*t)

Reference no: EM13265438

Questions Cloud

Would the bond be priced at a premium or discount : Kessen Inc.'s bonds mature in 7 years, have a par value of $1,000, and make an annual coupon payment of $70. The market interest rate for the bonds is 8.5%. Should an investor decide to purchase this bond today, would the bond be priced at a premi..
What rate of interest compounded annually : What rate of interest compounded annually is involved if
Plot the spectrum and the normalized spectrum of x : a) Plot the spectrum and the normalized spectrum of x[nT] = 2cos(20*pi*n*T + pi/8) + 4cos(40*pi*n*T + pi/8) for T = 0.01 b) Plot the spectrum and the normalized spectrum of
Obtain the work function of the metal : In a photoelectric effect experiment, visible radiation of energy 2.68 eV is incident upon a metal of unknown work function. determine the work function of the metal
What is the minimum sampling rate that can be used : What is the minimum sampling rate that can be used to obtain samples that completely specify the following signalx(t) = 10cos(20*pi*t) - 5cos(100*pi*t) + 20cos(400*pi*t)
What must flora show to recover damages from fast delivery : What must Flora show to recover damages from Fast Delivery?
Find the initial and final value of the time function : Use the initial and final value theorems to find the initial and final value of the time function corresponding to the following Laplace transform X(s) = x/(s+1)(s+4)
How low would the interest rate on the loan : How low would the interest rate on the loan with the compensating balance have to be for you to choose it?
Would the breakeven point increase or decrease : Would the breakeven point increase or decrease if the variable costs move from 40% to 45% of sales (all else constant)? Pick one.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate the length of side ut and the area of the plot

An engineer is required to survey a nonrectangular plot of land but is unable to measure side UT directly (see Figure 2.11). The following data are taken: RU=121.0m, RS=116.0m, ST=83.5m, angle RST= 113 degrees

  Determine the load current and the load voltage

a. Determine the voltage regulation, the load resistance, the armature resistance, and the developed torque at full load. b. The speed of the generator is decreased to 1200 rpm, and the load resistance is unchanged.

  What approximate minimum ber is required for voice signals

What approximate minimum BER is required for voice signals, data signals and what is the approximate BER level for the optical fiber systems ?

  Interface binary i/o devices to the microcontroller

Interface binary Input Output devices to the microcontroller

  Explain signals obtained separately in the radio receiver

How are the left (L) and right (R) signals obtained separately in the radio receiver to drive the dual channel audio amplifier and speakers?

  Design a sequential mealy circuit with two inputs a and b

Design a sequential Mealy circuit with two inputs A and B, and output X using JK flip-flops. The circuit produces an output X = 1 when it detects the sequence of either A = 00 or B = 11, otherwise X = 0.

  Describe what will happen on the circuit for present state

A. Make a two bit counter with The input X =0 makes the counter count from 0-3-1-0 and X=1 goes from 0-1-2-3-0. Choose two different types of flip flops to implement it. B. Describe what will happen on your circuit when the present state is 2 and ..

  What sizes of transformers are used for power lines

(1) check a diode out with a regular ohm meter (2) Give an example of where a half wave, full wave or bridge rectifier is used. (3) What sizes of transformers are used for power lines

  Indicate what floor the elevator is at

If someone presses the 1 or First floor button, the elevator should go to the 1st floor, open the door and remain in this state for a small amount of time, then close the door. Assume the elevator takes one clock cycle to travel.

  Determine the algebraic sign of the voltage sources

where the assigned loop current leaves the voltage source. If current leaves the voltage source at its positive terminal, the voltage would be positive and if it leaves the voltage source at its negative terminal,the voltage would be negative.

  Compute and plot the 128 point fft of a cosine wave

Compare the differences in the FFT result. Explain why even though the inputs to both FFTs are the same cosine waves, the shapes of the FFTs are different. Calculate, plot and compare the results of the 512-point FFT of the above signal.

  What is minimum bandwidth of the telephone line to transmit

The output power of the digital transmitter is 0 dBm and the link has a constant attenuation of 50.0 dB. At the input to the receiver, the equivalent AWGN noise power is – 70 dBm. Assume implementation margin is 0 dB when calculating BER in ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd