What is the minimum radius that can be cleared

Assignment Help Civil Engineering
Reference no: EM13545637

A two lane hwy with 12' lanes is to be reconstructed to a design speed of 50 mph. Due to right of way restrictions, the largest distance that can be cleared from the edge of the road is 10'. What is the min. radius?

Reference no: EM13545637

Questions Cloud

What contour intervals will be drawn if a 50ft interval : An area that varies in elevation from 463ft - 634ft is being mapped. What contour intervals will be drawn if a 50ft interval is used? Which lines are emphasized?
The mass center of the unbalanced disk of weight w is locate : The mass center of the unbalanced disk of weight W is located at G, which is a distance of R/2 from the center for the disk. In the equilibrium postition
What will be the discharge through the pipe : A pump having the characteristics given in figure 14.9 ( N=2133.5 rpm, n=35.6 rps, D=37.1 cm) pumps water at 25 degree C from a reservoir at an elevation of 366 m to a reservoir at an elevation
Find the operating points (q) for one pump : The pump curve for a given pump is represented by hp,pump=20 (1-(Q/100)^2) where hp,pump is the head provided by the pump in feet and Q is the discharge in gpm.
What is the minimum radius that can be cleared : A two lane hwy with 12' lanes is to be reconstructed to a design speed of 50 mph. Due to right of way restrictions, the largest distance that can be cleared from the edge of the road is 10'. What is the min. radius?
What is the tensile force on the weld per foot : Due to a leak in Pump Station 1,the Alaska pipeline is shut down briefly.The pipe line is half full.Assume the pipe is welded horizontally at its midpoint.What is the tensile force on the weld per foot? Assume Ø=40”and ?oil=53.55lb/ft3.
The average return period of the median value : The probability that, for a 2-year period, the peak flow rate will equal or exceed the median value in the second year, but not in the first year?
What happens after the memory is full : Assuming approximately 19,296 data points can be held in memory, with a 21X Datalogger (CR23X Micrologger), capturing battery voltage; panel temperature
Compute the maximum fiber stress : An S 12x40.8 of A36 steel in a building is supported as a simple beam having a span equal to 17ft 6in. and carries a uniform load equal to 1.60 klf, which includes the weight of the beam over the entire span.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the shear stresses at each of the following points

A 6 inch X 4 inch rectangular beam is subjected to a maximum shear force of 1900 lbf. Determine the shear stresses at each of the following points on the beam cross section:

  What is the hydraulic conductivity of the other two soils

A permeameter with a cross-sectional area of 400 cm2 contains 3 soils in 50 cm thick layers. A total head difference of 2.0 metres results in a flow rate of 100 cm3/s. The head loss through the top layer of soil is 50 cm.

  Four forces act on a small airplane

The slope distance and zenith angle measured from point P to pointQ were 1876.253m and 87.33'24 degrees, respectively. The instrumentand rod target heights were equal. If the elevation of point P is227.965m, above datum, what is the elevation of poin..

  What force will need to be applied to block downward to hold

A wood cube with 9 inch sides is inserted into water. The specific gravity of wood is 0.60. What force will need to be applied to the block downward to hold the wood cube completely submerged in water

  Estimate total cost and cost per linear foot for furnushing

estimate the total cost and cost per linear foot for furnushing and driving steel-sheet piling for construction of the basement of a building, 150 by 240 ft. the piles will be 22 in. wide, 18 ft. long, and weigh 40.3 Ib/Lin ft.

  Determine the radial and transverse components

Knowing that the tension in the spring is70 N and the speed of the collar is 3.8 m/s as it passes through point A, determine, at that instant, the radial and transverse components of acceleration of the collar.

  What is diffusion flux assuming conditions of steady state

consider the diffusion of water vapor through a polypropylene (PP) sheet 2mm thick. the pressure of H2O at the two faces are 1 kPa and 10kPa, which are maintained constant.

  Develop an equation for a safe minimum design radius r

The speed limit for a highway is given as "V" in mph. The highway super elevation is given as "e" in ft/ft. The friction between tires and wet pavement is given as "f".

  Determine the normal depth-critical depth and velocity

A PVC pipe with a diameter of 30 inches will carry a flow of 20 cfs. the bottom slope is 0.005 and the roughness coefficient is 0.015. determine the normal depth, critical depth, velocity and the froude number.

  Generate suitable design information to produce max power

During the recent camping trip, a curious junior engineering student (like yourself) noticed that water is being discharged from a high reservoir to a stream in the valley through a 0.3 m diameter plastic pipe.

  Determine the force in each member of the truss

Determine the force in member AB Determine the force in member AE Determine the force in member BC Determine the force in member BE Determine the force in member CD

  Which method would be most likely to have the conductivity

If an analysis is made of the hydraulic conductivity of a site using permeameter tests of core samples, slug tests of monitoring wells, and pumping tests of production wells, it is often observed that the hydraulic conductivity as measured by each..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd