Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Refer to the RLC series circuit shown in Figure.
(a) What is the maximum output voltage vO (t) and at what frequency does it occur? Use Multisim and do an ac sweep from 10 Hz to 1 MHz, and then narrow your sweep until you find the frequency at which the peak occurs and the output voltage at that frequency.
(b) Bandwidth is defined as BW = fH - fL, where fH is the higher frequency at which the magnitude of the output is exactly 0.707 of the maximum value, and fL is the lower frequency at which the magnitude of the output is exactly 0.707 of the maximum value. What is the bandwidth of this circuit?
(c) What is the minimum output voltage vX(t) and at what frequency does it occur? Use Multisim and do an ac sweep from 10 Hz to 1 MHz, and then narrow your sweep until you find the frequency at which the minimum occurs and the output voltage at that frequency.
Using energy concepts, find the internal self inductance per unitlength of a loss-less, conductive solid wire of radius ρ. You may assume that the current is uniformlydistributed through the cross-section of the wire.
What is electric potential at the center of the circle and What is the electric field (magnitude and direction) at the center of the circle
A runner should STEAL a base if and only if the manager pulls his EAR and BOWs while patting his HEAD, or if he lifts his LEG and pats his HEAD without BOWing, or anytime he pulls his EAR without lifting his LEG. Sketch a minimal circuit that coul..
Build a 1Gbps link as long as possible without regeneration. Assume a transmitter power of 1mW and a receiver sensitivity of -30dBm for a BER of 10^(-9). The dispersion at 1.5 micron is 20 ps/km.nm, and the attenuation is 0.25 dB/km.
one disadvantage to using wireless nics is that they and the infrastructure needed to support them are currently
Consider the circuit shown below, with all the switches S1 through S400 initially open. - Calculate the resulting current I in the circuit in its final state.
Metal sphere 1 has a positive charge of 8.0 nC. Metal sphere 2, which is three times the diameter of sphere 1, is initially uncharged. The spheres are then connected together by a long, thin metal wire. What are the final charges on each sphere
given the vector field g 2xsup2y ax - 2z-x ay 3xyz az find a g at p2-34 b a unit vecotr in the direction of g at p
If 20 MHz of total spectrum is allocated for a duplex wireless cellular system and each simplex channel has 25 KHz RF bandwidth, find: (a) the number of duplex channels (b) the total number of channels per cell site, if N = 4 cell reuse is used.
A 3-phase 230 V, 9 kVA, 0.9 PF (lagging) load is supplied by 10 kVA, 1330/230 V, 60 Hz three-phase transformer connected in Y-?. The equivalent impedance of transformer referred to the low-voltage side is 0.12 + j0.25.
the first microprocessors were packaged as a dual inline pin dip integrated circuit. would dip and quad versions have
Assume a 16-bit fixed point, two's complement representationwith 8-bits of integer and 8-bits of fraction. What is therepresentation of the following values in hexidecimal.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd