What is the minimum bottom width to effect the depth

Assignment Help Civil Engineering
Reference no: EM13313902

A trapezoidal channel is to be designed to carry a discharge of 250 cfs at a normal depth of 3.5 ft. The channel is running on a slope of 0.005 ft/ft and the side slopes can be no steeper than 2.5 H on 1 V. The channel is earthen and will have an estimated Manning n value of 0.03. What is the minimum bottom width to effect the required normal depth?

Reference no: EM13313902

Questions Cloud

What is marys angular speed : Mary and her younger brother Alex decide to ride the carousel at the State Fair. What is Mary's angular speed %u03C9M and tangential speed vM
Determine the length of the water column : Mercury is poured into a U-tube. The left arm of the tube has cross-sectional area A1 of 10.4 cm2, Determine the length of the water column in the right arm of the U-tube
Estimate what is the total volume of runoff : It rains 3.0 in. on a 20.0 acre watershed. What is the volume of rainfall excess if 30% of the watershed area is a lake and infiltration on the soil is estimated at 1.0 in. What is the total volume of runoff
Develop a communication plan for the company : Develop a communication plan for the company
What is the minimum bottom width to effect the depth : A trapezoidal channel is to be designed to carry a discharge of 250 cfs at a normal depth of 3.5 ft. The channel is running on a slope of 0.005 ft/ft and the side slopes can be no steeper than 2.5 H on 1 V.
Find the conjugate depths of the jump formed in a channel : The discharge through a 6.0 ft wide rectangular channel is 200.0 ft3/s. Find the conjugate depths of the jump formed in such a channel if 3.5 ft of energy head is lost through it.
Calculate the depth of flow 2 km upstream of the dam : A 12.0 m rectangular channel, having a bed slope of 50 cm/km and a Manning roughness coefficient of 0.015, conveys water at a normal depth of 1.0 m. A dam is built across the channel at which the water depth is 2.0 m.
Calculate the resistance per unit length of the wire : When a potential difference of 2 V is applied across the ends of a wire of 5 m length, a current of 1A is found to flow through it. Calculate: the resistance per unit length of the wire
How much time does it take for the ball to hit the ground : A ball rolls off a platform that is 6.8 meters above the ground. The ball's horizontal velocity as it leaves the platform is 7.4 m/s.How much time does it take for the ball to hit the ground

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find the void ratio and specific gravity of solids

A specimen of saturated soil has a water content of 145 percent and a total unit weight of 84 pcf. Find the void ratio and specific gravity of solids.

  Determine the centroid-moment of inertia and section modulus

THE HOME DEPOT IN RED HOOK ,BROOKLYN IS LOOKING TO RENOVATE THEIR STEEL ROOF TRUSS.YOU HAVE BEEN ASKED TO DETERMINE THE CENTROID,MOMENT OF INERTIA,SECTION MODULUS AND RADIUS OF GYRATION OF THE DOUBLE ANGLE.

  What diameter is required if the concrete pipe is to carry

A ciricular sewer is laid on a slope of 0.5%. What diameter is required if the concrete pipe is to carry 25 cfs If the desired design mean suction velocity is between 3 and 7 ft/s, is the design acceptable

  Radius of the steel wire ehen stretching with other wire

The aluminium wire has a radius of 1.1mm. What must be the radius of the steel wire if it is to stretch the same distance as the aluminium wire, so that the two wires maintain equal lengths after the masses are attached?

  Determine the magnitudes of accelerations of points a and b

The center 0 of the wheel is mounted on the sliding block, which has an acceleration of a0= 8 m/s2 to the right. At the instant when theta=45 degrees, theta dot is = 3 rad/s and theta double dot is = -8 rad/s2.

  Determine what would be the co concentration in the box

A simple way to model air pollution over a city is with a box model that assumes complete mixing and limited capability for the pollution to disperse horizontally or vertically except in the direction of the prevailing winds

  What considerations would made with regards to cement type

You are a construction engineer working on a large concrete foundation project, involving the placement of over 500,000 c.y of concrete. The construction site is adjacent to a salt-water source (bay) & it is decided to set up a concrete batch plan..

  Design the roof slab as a one-way slab system

Design the roof slab as a one-way slab system and use the worst case design scenario to determine the reinforcing for the entire roof

  How would the economies of construction be obtained

For a metal and wood structure, how would the economies of construction be obtained (pertaining to the mean and standard deviation of a probability of failure graph)?

  Determine was driver exceeding the speed limit at time zero

A car is traveling along a road at a uniform velocity when at time zero the driver recognizes a hazard. At a moment 0.8 seconds later the driver brakes her vehicle , resulting in her vehicle sliding 90 ft in the same direction

  What is the true weight of the water and tank at 10 sec

A large tank is used to calibrate the reading from a flow meter. Measurements of the system weight as a function of time are made. Water enters the tank vertically from the flow metering system at a speed of 20 ft/sec through a 1.5 in.

  Determine the heat transfer rate from the compressor

In a refrigeration system Refrigerant 22 enters the compressor at 150 kPa and -10 C. It leaves the compressor at 1.0 MPa and 90 C. Assume the mass rate of flow through the compressor is 0.016 kg/s

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd