What is the mechanical power supplied to the load in watts

Assignment Help Electrical Engineering
Reference no: EM13276086

A motor is supplying 60 N · m of torque to its load. If the motor's shaft is turning at 1800 r/min, what is the mechanical power supplied to the load in watts? In horsepower?

Reference no: EM13276086

Questions Cloud

Define each part of a financial plan : Define each part of a financial plan and discuss the importance of these components in managerial decision making.
Estimate the capacitance of the capacitor : a 100v dc battery, a resistor and a capacitor are connected in series. The capacitor is initially uncharged. estimate the capacitance of the capacitor
Show what decoding logic is required to decode each state : Given a BCD decade counter with only the Q outputs available, show what decoding logic is required to decode each of the following states and how it should be connected to the counter . A HIGH output indication is required for each decoded state .
What is the net electric flux through the surface : 31.3 million excess electrons are inside a closed surface. what is the net electric flux through the surface
What is the mechanical power supplied to the load in watts : A motor is supplying 60 N · m of torque to its load. If the motor's shaft is turning at 1800 r/min, what is the mechanical power supplied to the load in watts In horsepower
Determine the length of the rough patch : On an essentially frictionless horizontal ice-skating rink, a skater moving at 3.1m/s encounters a rough patch that reduces her speed by 42% to a friction force that is 24% of her weight
What will be the cost of the newly issued common shares : You have advised the firm that flotation costs will be 8% per share. What will be the cost of the newly issued common shares?
How does a patient decide where to go for treatment : What do patients expect from medical treatment, and what leads people to seek treatment and how does a patient decide where to go for treatment?
What would be the retained earnings balance at the end : The tax rate is 40 percent. What would be the retained earnings balance at the end of the year?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate alpha-omega-sub-delta and omega-sub-zero

The source-free circuit depicted in Fig. 9.1 is constructed using a 10mH inductor, a 1mF cPcitor, and a 1.5k ohm resistor. a) Calculate alpha, omega-sub-delta, and omega-sub-zero. b) write the equation which describes the current i for t>0.

  Find range of values of fc can be used to transmit signal

The signal x(t) = 20*sinc2(400t) is input to a ring moodulator. Sketch the spectrum of vout and find the range of values of fc that can be used to transmit this signal.

  What values do the instructions load into the accumulator

Given the memory locations, values below, and one-address machine with an accumulator (the accumulator is the default destination), what values do the following instructions load into the accumulator

  Determine the entropy generated for the process

An adiabatic piston cylinder contains 1 kg of R-134a. Initially the conditions inside the piston are 200 kPa and 0 degrees C. An electric heater inside the device runs with constant voltage of 110 V and a constant 0.1A of current for one hour

  Convert the value entered in r3 from hexadecimal to ascii

Students should type up, assemble and emulate the BIN2ASCII program which converts the value entered in R3 from Hexadecimal to ASCII. This should be done by dividing R3 by 10 (decimal) and converting the remainder to ASCII

  Determine the thermal equilibrium recombination

A semiconductor, in thermal equilibrium, has a hole concentration of p0 = 2x1016 cm-3. The minority carrier life time = 3x10-7 s. (Assume, ni = 1010 cm-3)

  Illustrate per-phase analysis of power transmission system

The source has an abc-phase sequence. At the wye-connected load, the phase-a voltage Va'n' has phase angle (theta)a'n' = 60 degrees and the phase impedance is (10 + j15) ohms. Further, the line impedance per phase is (1.1+ j1.5) ohms

  Explain what will happen in device in terms of w and charges

A pn junction may be formed by depositing a single crystal film of uniformly doped p-silicon onto a substrate that has been doped n-type. The substrate is 500um thick, and the film is 20um thick. The substrate has a 5 ohm-cm resistivity.

  Explian what is the attenuation per octave

What is the attenuation per octave between 1 kHz and 10 kHz? What is the increase in attenuation between 5 kHz and 10 kHz?

  What are the prospects for offshore oil beds

Research about origin, formation process, and age of oil. What type of biota contributed to oil formation How is that linked to marine environment being conducive to oil formation What are the prospects for offshore oil beds

  Determine the position x and the tension in the cord

Determine the position x and the tension in the cord that is required for equilibrium. The cord passes through the smooth ring at B and has an unstretched length of 6ft and stiffness of k = 50lb/ft.

  Explain one signaling element is used to represent

Bandwidth, In a given communications system, one signaling element is used to represent 64 bits. The required data rate is 1.789 Mbps.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd