What is the maximum shear stress in the liquid

Assignment Help Civil Engineering
Reference no: EM13544454

A liquid flows between parallel boundaries

The velocity distribution near the lower wall is given in the following table:

y in mm V in m/s

0.0 0.00

1.0 1.00

2.0 1.99

3.0 2.98

If the viscosity of the liquid is 10–3 N-s/m2, what is the maximum shear stress in the liquid?

Answer should be in the units: N/m^2

Reference no: EM13544454

Questions Cloud

What is the minimum distance that connects all the nodes : What is the minimum distance that connects all the nodes and what is the minimum possible time required for completing the  project?
What is the volume of this cloud in cubic miles : Calculate the volume (in ft^3) of a person of 180 lbf weight, assuming reasonable SG for the human body.
What is the maximum grade this vehicle : A 2500-lb car (CD = 0.35, Af = 25 ft^2, and ? = 0.002378 slugs/ft^3) has 14-inch-radius wheels, a drivetrain efficiency of 90%, an overall gear reduction ratio of 3.2 to 1
What is the maximum coefficient of road adhesion needed : A rear-wheel-drive 3000-lb drag race car has a 200-inch wheelbase and a center of gravity 20 inches above the pavement and 140 inches behind the front axle
What is the maximum shear stress in the liquid : If the viscosity of the liquid is 10–3 N-s/m2, what is the maximum shear stress in the liquid?
Determine graphically the magnitude and direction : The cable stays AB and AD help support pole AC. Knowing that the tension is 120 lb in AB and 40 lb in AD, determine graphically the magnitude and direction of the resultant of the forces exerted by the stays at A using (a) the parallelogram law, (b) ..
Calculate what is the frisbees rotational inertia : A 106g Frisbee is 18cm in diameter and has half its mass spread uniformly n the disk and the other half concentrated in the rim. What is the Frisbee's rotational inertia
Determine the maximum tension t that can be exerted : If a hook can sustain a maximum withdrawal force of 250 N inthe vertical direction, determine the maximum tension, T, that can be exerted.
Determine the amount of air added to the tank in lbm : A rigid tank contains 40 lbm of air in 20 psia and 70 degrees F. More air is added to the tank untill the pressure and temperature rise to 35 psia and 90 degrees F, respectively.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Estimate what is the critical slope of the channel

A trapezoidal channel cut into rock has a bottom width of 4 ft, side slopes of 1:1 and a channel slope of 0.0005. What is the critical slope of the channel.

  Determine required width and volume flowrate of the model

The spillway for a dam is 20 m wide and is designed to carry 125 m3/s at flood stage. A 1:15 ratio model is constructed to study the flow characteristics through the spillway. The effects of surface tension and viscosity can be neglected.

  Consider the process of baking potatoes in coventional oven

Consider the process of baking potatoes in coventional oven.Can the hot air in the oven be treated as a thermal energyreservoir? Explain

  Determine the internal shear force and moment in the jib

The jib crane supports a load of 750 lb from the trolley which rides on the top of the jib. The members of the crane are pinned together at B, E, and F and supported by a short link BH.

  Define base isolation technique has become the method

Base isolation technique has become the method of choice for structural design of buildings and bridges located in highly seismic areas in recent years.

  Question in structure analysis concrete column with

question in structure analysis concrete column with dimension square 300 mm300 mm length 3m and concrete grade c3545.

  Determine the minimum height on the wall from hose

Determine the minimum height on the wall to which the firefighter can project water from the hose, so that the water strikes the wall horizontally. The speed of the water at the nozzle is Vc=48ft/s.

  Pressure on the soil if theta is given

A pipe is to be installed under the ground on a bed of aggregate 6 in. thick. The entire weight on the aggregate from pipe and soil above the pipe is 1800 lbs. per linear foot of pipe. What is the pressure on the soil if theta is 45 degrees? Assum..

  Find the change in depth and in absolute water level produce

Find the change in depth and in absolute water level produced by a) a smooth upward step of 1 ft b) a smooth donward step of 1 ft, in the channel bed c) find the maximum allowable size of thw upstream flow to be a possible as specified

  Determine the probability that ball is white

Box I contains 3 red and 5 white balls, while Box II contains 4 red and 2 white balls. A ball is chosen at random from the first box and placed in the second box without observing it's color. Then a ball is drawn from the second box.

  Determine by trigonometry the required angle of forces

two forces applied as shown to a hook support. knowing that the magnitude of P is 35 N, determine by trigonometry the required angle if the resultant R of the two forces applied to the support is to be horizontal and the corresponding magnitude of..

  Prove that the fluid in the pipe will flow from a location

Assume that you have a constant diameter pipe that has no pumps or turbines connected to it.Prove that the fluid in the pipe will flow from a location with high piezometric pressure to one with low piezometric pressure.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd