What is the maximum shear force due to the crane

Assignment Help Civil Engineering
Reference no: EM13874247

The beam is supporting a concentrated load due to a 20 tons crane which moves from A to F. What is the maximum shear force due to the crane at support B? Also determine the maximum moment due to the crane at  point B and C.

2146_IMAG0724.jpg

Reference no: EM13874247

Questions Cloud

Explain the rationale behind why an investor might choose : Explain the rationale behind why an investor might choose NOT to sell bonds
Interest coverage ratio of sevcik company : During the current year, Sevcik Company had pretax income from continuing operations of $19,200, which included interest expense of $4,000.
Grained sharp and hard : Sand for concrete must include a statement following except:A. grained sharp and hard. B. Does not contain the mud more than 5%. C. Does not contain organic ingredients. D. Large grains of uniform / common.E. Does not contain salt.
Discuss the importance of continuous monitoring of portfolio : Discuss the importance of continuous monitoring of portfolios
What is the maximum shear force due to the crane : The beam is supporting a concentrated load due to a 20 tons crane which moves from A to F. What is the maximum shear force due to the crane at support B? Also determine the maximum moment due to the crane at  point B and C.
Speculate on the organizations ability to meet its financial : Speculate on the organization's ability to meet its financial obligations
Depreciation expense is listed as a separate item : The following accounts are taken from the December 31, 2010 adjusted trial balance of the Reed Company:
Assess the responsibility of individual smokers for the harm : In no fewer than 750 but no more than 1,250 words, assess the responsibility of each of the following three groups of people for the harm caused by smoking light and ultra light cigarettes. In your essay, rank the three groups in order from most r..
What is your analysis of this debate : What is your analysis of this debate? Which of the authors do you most agree with and why? Do you have an analysis that differs from all of the articles? If so, why?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Discuss the minimum alignment required to establish the

Explain the process for establishing a centerline for a roadway for an existing road. Include a description of the types of property markers used as well as any problems a surveyor may encounter in this process

  What would be magnitude of coresponding forces on full scale

Offshore oil exploration platform is expected to encounter current of 3 m/s wave height 4 m and periods 15 seconds. A 1 in 20 scale modes is to be build and tested in hydraulic laboratory to determine the forces on the full scale structure.

  Determine the final temperature of the steam

The force on the piston is such that it maintains a constant pressure of 400 kPa inside. A valve is now opened nad steam at 1 MPa, 200 degrees C is allowed to enter the cylinder until the volume inside increases to 0.04 m^3.

  Determine the displacement of the beam at each end

A rigid beam (AB), 12 feet in length, with a point load of 9 kips (4 feet from A) is resting on two short steel rods (AC & BD). Diameter of Rod AC is 1 inch, Rod BD diameter is 2 inches. Assuming no buckling in rods, Determine the displacement of the..

  What are the speed and acceleration of the disks top

disk of radius R=7 in. spins at a constant angular speed of w=500rpm in the clockwise direction. If the disk is released from rest far above the ground, what are the speed and acceleration of the disk's top C point after it has fallen h=3ft

  A well hit golf ball travels at a speed of 150 mph

A well hit golf ball travels at a speed of 150 mph ( 220 ft/s) as it leaves the tee. The golf ball has a diameter of 1.70 in and weighs 0.099 lb. Assuming standard atmospheric conditions (mu, u air = 3.74 * 10^-7 lb-s/ft2 and rho = 0.00238 slug/ft3) ..

  What is the equivalent pressure drop in standard atmospheres

A HEPA (high efficiency particulate air) filter is monitored periodically for replacement. Specifications state that if the pressure drop across the filter exceeds 1 inch of water, the filter should be replaced.

  Determine void ratio and dry unit weight of compacted sample

A soil sample is prepared in the laboratory by mixing a certain amount of dry soil with 10.5 wt% water. The relative density of the grains of the material is equal to 2.7.

  How long would it be before company could sell the property

A multinational engineering consulting firm that wants to provide resort accommodations to certain clients is considering the purchase of a three-bedroom lodge in upper Montana that will cost $250,000.

  Determine the initial void ratio assume also that settlement

A square building (15 m × 15 m in plan) is to be constructed on a site where the soil profile consists of 3m of clay with an over-consolidation ratio that varies from 5 at the surface to 2 at 3m overlying a 5m thick clay

  Write and expression for a in terms of b that makes

For the following velocity profiles state whether they are steady or unsteady and whether they are 1-D, 2-D or 3-D.

  Find the rate of biological growth

Two identical complete-mix activated sludge units are connected in series; one-half of the sludge recycle flow rate, QR, is recycled to the primary effluent pipeline which handles a flow rate Q, and the other half is recycled to the effluent line fro..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd