Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A three-phase, 5kVA, 208 V, four-pole, 60Hz, Y-connected synchronous generator has negligible stator winding resistance and a synchronous reactance of 8 ohms per phase at rated terminal voltage.
a.) Determine the induced internal voltage and torque angle when the machine is delivering rated kVA at 0.8 PF lagging. Draw the pharos diagram for this diagram.
b.) What is the maximum possible power that generator can supply in part a?
c.) Field current is now increased by 20% without changing the prime mover power. Find the stator current, power factor and reactive power supplied by the machine.
Discuss the differences between series and parallel circuits. What are some advantages and disadvantages of each type Discuss why the total power equals the sum of the individual values of power, whether a series circuit or a parallel circuit is u..
A glass tube with a cross-sectional area of 9^-2 m^2 contains an ionizd gas. The densities are 10^15 positive ions/m^ and 10^11 free electrons/m^3. Under the influence of an applied voltage, the postive ions are moving.
A three-phase delta connected load has a phase resistance of 15 ohms and a phase reactance of 17 ohms when connected to a 480VAC 60HZ line. What is the phase impedance, phase current power factor, and total power delivered to the load
Imagine a circuit consisted of two DC power sources of 12 volt and 10 volts. The negative terminals of these power sources are wired together. Assume that the positive terminals of these power sources are labeled as A and B respectively.
A temperature sensor has a static transfer function of 0.15mV/degrees C and a time constant of 3.3 s. If a step change of 22 degress C to 50 degress C is applied at t = 0, find the output voltages at 0.5s, 2.0s, 3.3 s, and 9s.
You balanced a pump impeller by placing a 5 gram weight at a radius of 100 mm. The original vibration amplitude was 10 mm/s, and after adding the balancing weight, the vibration is 1 mm/s. The speed of the pump is 1500 rpm and the weight of the im..
What fixed point unsigned representation, with how many bits and how many bits to the left of the binary point, should we use if we need to represent numbers in the range 0 - 100 with a resolution of .001 or better
A dc shunt motor drives a centrifugal pump at a speed of 1000rpm when the terminal voltage and the line currents are 200V and 50A, respectively. The armature and field resistance are 0.1 ohm and 100 ohm respectively.
The average noise power per unit bandwidth measured at the front end of an AM receiver is 10^(-3) watt per Hertz. The modulating wave is sinusoidal, with a carrier power of 80 kilowatts, and a sideband power of 10 kilowatts per sideband.
If designing a computer configuration for use as a workstation for one specific application, what aspects of the software need to be considered as part of the design process?
Write a C program for the 68HCS12 microcontroller to send the pattern 0x55 to byte-sized Memory Location "OUT1" and then call a delay function. The delay function should generate a delay of two milliseconds.
Consider the problem of using a low-voltage system to power a small cabin. Suppose a 12-V system powers a pair of 100-W lightbulbs (wired in parallel). a. What would be the (filament) resistance of a bulb designed to use 100 W when it receives 12 V
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd