What is the maximum population that can be served

Assignment Help Civil Engineering
Reference no: EM13560411

1.A time interval of 1.5 hours is recorded for a 6 inch drop of water level in a percolation (perc) test hole. What is the perc rate? How many laterals would be required in the leaching field to serve a 5 bedroom house, if the trench width is 2 feet and the maximum trench length is 80 feet?

2.What is the maximum population that can be served by a 900 mm diameter main sewer constructed on minimum grade? If sewage flow in the pipe never exceeds a depth of 600 mm, estimate the actual population contributing flow to the main.

Reference no: EM13560411

Questions Cloud

Find the length and width of a square basin for virus : Find the length and width of a square basin for virus disinfection of a flow of 6 MGD. You may assume a depth of 5 ft, a C?t product of 10 (mg/L) ?min for 1.5-log removal, and a target free chlorine residual of 0.6 mg/L.
When you determine the number of filters needed : A water treatment plant is being designed for a flow of 1.6 m^3/s. How many rapid sand filters, using only sand as the medium, are needed for this plant if cross-sectional area of each filter is 10 m x 20 m?
How many pounds of copper sulfate should be dissolved in the : You have been hired by your local golf course as an environmental consultant to stop the rapid growth of algae in its premier lake at the 18th hole. You have determined that a 0.5 ppm concentration of copper sulfate should be applied
Determine an appropriate pipe diameter and slope : A 100-m reach of sewer is to have a minimum capacity of 200 L/s. The street elevation at the upper manhole is 305.55 m and at the lower manhole is 303.05 m. Determine an appropriate pipe diameter and slope for this reach
What is the maximum population that can be served : What is the maximum population that can be served by a 900 mm diameter main sewer constructed on minimum grade? If sewage flow in the pipe never exceeds a depth of 600 mm, estimate the actual population contributing flow to the main.
What is the net force of the water on the block : A horizontal het of water at 5 degrees celsius strikes a block and is deflected upward 30 degrees. The mass flow rate of the water is 1.75 kg/s. The mass of the block is 1.30 kg. The jet has a cross sectional area of 10 cm^2
Explain senior management role : Explain senior management's role in preparing the organization to shift from a catalog-based retailer to an Internet retailer. Provide evidence of whether the transition was seamless or problematic from a management perspective. Provide support for y..
Ensure the application of the concepts and techniques learnt : Prepare the Outline of the Final Project based on your approved Project Proposal submitted in Week 4. The Outline must be structured on the Proposal to ensure the application of the concepts and techniques learnt in this module.
Calculate the critical radius and the number of atoms : Calculate the critical radius and the number of atoms in the nucleus of the homogeneous nucleation in GERMANIUM. The latent heat of fusion is 8100 cal per g-mile (atom) and the coefficient of linear expansion is 5.75*10^-6 per K

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the magnitude of its acceleration at the instant

car traveling along a circular curve that has a radius of 50m. if its speed is 16m/s and is increasing uniformly at 8 m/s^2 determine the magnitude of its acceleration at this instant

  Is this level dangerous to the fish population

A lake has a volume of 750,000 m3 (dimensions 15 m deep, 100 m wide, and 500 m long) and behaves as two completly mixed cells. Cell 1 makes up 40% of the lake ( dimensions 15 m deep, 100 m wide, and 200 m long) cell 2 makes up 60% of the lake (dimens..

  Calculate factor of safety if the material does not yield

The program should use both the maximum shearing-strength criterion and the maximum-distortion-energy criterion. It should also print the values of the principal stresses and, if the material does not yield, calculate the factor of safety.

  Determine the rate of superelevation on the c

A curved section of a two-lane highway measured in the field was found to be 22 feet wide and have an elevation difference of 1.37 feet between the outside and inside edges of the pavement

  Calculate the amount of each phase present in a 1-kg alumina

Calculate the amount of each phase present in a 1-kg alumina refractory with composition 70 mol % Al2O3- 30 mol% SiO2 at 2,000 C , 1,900 C and 1,800 C

  Determine the maximum radius r

Determine the maximum radius R (to the nearest 10m) so that there are at least 200m of tangent between the two curve systems and determine the Pl, ST., and CPI stations

  Briefly explain the purpose of the international space

q1. briefly explain the purpose of the international space station and list the name of all space agencies involved in

  Calculate pump head and equate it to frictional head loss

A 420 kW pump delivers gasoline at a rate of 1.28 m^3/s through a horizontal pipe. The average roughness height is 0.005 cm. The total length of the pipe is 46 m. Calculate the pipe diameter.

  Use the gamma of water is equal to 1000 kg/m^3

A horizontal 150mm pipe, in which 40 l/s of oil (S=.8) is flowing, contracts to a 75 mm diameter (left to right). If the pressure in the 150mm pipe is 300kPa, calculate the magnitude and direction of the horizontal force exerted on the contraction

  What is the precision of the work

The sides of a closed figure have been measured and found to have a length of 4133.64 ft. If the total error in the measurements is equal to .15 ft, what is the precision of the work?

  What is the underflow flow rate

A settling tank in a water treatment plant has an inflow of 2m3/min and a solids concentration of 2100 mg/L. The effluentfrom this settling tank goes to sand filters. Theconcentration of sludge coming out of the bottom (the underflow) is18,000 mg/L, ..

  Calculate fluid viscosity of torque on the inner cylinder

If the diameters are 2 cm and 4 cm, respectively, calculate the fluid viscosity if the torque on the inner cylinder is measured to be 0.0026 N*m.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd