Reference no: EM131285242
Electronics Lab: Bridge Rectifier
Introduction:
The lab is based on half-wave and full-wave rectifiers and taking that knowledge to build a bridge rectifier.
Materials and Equipment:
Materials:
• Simulated Parts (Multisim):
o A 30/3 Vrms center-tapped transformer
o Two diodes 1N4001
o Two 2.2 kΩ resistors
o One 100 μF, 50 V electrolytic capacitor (any voltage rating is fine since is simulation only)
o One fuse (any rating is fine since is simulation only)
Equipment:
Virtual Instruments (Multisim):
o Tektronix Oscilloscope
o Agilent Multimeter
o Agilent Function generator
Procedure:
3. Construct the bridge rectifier circuit shown in Figure 1. Notice that no terminal of the transformer secondary is at ground potential (some simulation software will not run if it is not connected to the ground, check yours). The input voltage to the bridge, VSEC, is not referenced to ground. Make sure to include resistor tolerance of 5%.
4. Use a function generator to provide VAC and run the simulation.
5. Use a multimeter to measure VSEC (rms) and then use the oscilloscope to measure the peak output voltage (VLOAD) without a filter capacitor. Tabulate all data gathered.
Figure 1
Connect the 100 μF capacitor in parallel with the load resistor. Measure VLOAD, the peak-to-peak ripple voltage VRIPPLE, and the ripple frequency. Tabulate all data gathered and compare the results with and without the filter capacitor.
|
|
Without the capacitor
|
With the capacitor
|
|
Output load voltage VLOAD
|
|
|
|
Peak-to-peak ripple voltage VRIPPLE
|
|
|
|
Ripple frequency
|
|
|
5. Choose a diode among the four connected to the bridge and open it. Simulate an open diode in the bridge and explain what happens to the output voltage, the ripple voltage and the ripple frequency?
6. Investigate the effect of the load resistor on the ripple voltage by connecting a second 2.2 kΩ, 5% tolerance, and load resistor in parallel with RL and C1 in the full-wave circuit of Figure. Measure the ripple voltage. Captures a screenshot.
Review questions:
7. Compare a bridge rectifier circuit with full-wave rectifier center-tapped circuit which you did in Lab 2. Which circuit has the higher output voltage?
8. Explain how you could measure the ripple frequency to determine if a diode were open in a bridge rectifier circuit.
9. What is the maximum dc voltage you could expect to obtain from a transformer with a 3 Vrms secondary using a bridge circuit with a filter capacitor?
Deliverables:
10. Measure the voltage VSEC and the output load voltage, VLOAD without a filter capacitor. Capture the screenshots of your measurements.
11. Measure the output load voltage, VLOAD, with the capacitor and the peak-to-peak ripple voltage, VRIPPLE, in the output. Capture the screenshots of your measurements. Also, measure the ripple frequency. Table with all the data gathered for the circuit with and without the capacitor.
12. Follow the template "Lab Report Template" to compile the report and make sure to check the report against the grading rubric below. The template can be found in the "Tools and Templates" link in the navigation center.
13. Make sure to include the table, calculations, screenshots of the measurements and the answer to the questions.
|
Create an allowance for doubtful accounts
: Why do companies need to create an allowance for doubtful accounts? Further, consider the following statement: "The income statement approach used to estimate bad debts is based on Accounts Receivable on the Balance Sheet." Do you agree or disagree w..
|
|
Taxpayers in regards to certain itemized deductions
: Give details about Temporary Exemptions for taxpayers in regards to certain itemized deductions. How are certain itemized deductions are limited? Identify special rules and the deductions they pertain to.
|
|
Describe the population of the area in terms of age
: Describe the population of the area in terms of age, income, education, ethnic background, marital status, occupation, and housing.
|
|
Calculate the equivalence ratio
: Calculate the equivalence ratio, the maximum pressure and temperature achieved during the cycle, and also the composition (by volume) of the dry exhaust gas.
|
|
What is the maximum dc voltage you could expect to obtain
: What is the maximum dc voltage you could expect to obtain from a transformer with a 3 Vrms secondary using a bridge circuit with a filter capacitor?
|
|
Where does the little mermaid come among her sisters
: Where does the little mermaid come among her sisters? How do you think she felt about this order?Who was the father of the Little Mermaid? How did he treat his children?
|
|
The combination approach to the modified internal rate
: What is the purpose of financial statement analysis and who would be the main users? Do you think it is important? A project has projected cash flows of -$148,500, $32,800, $64,200, -$7,500 and $87,300 for years 0 to 4, respectively. Should this proj..
|
|
What is the role of perceived risk in the decision process
: Explain habitual decision making, limited problem solving, and extended problem solving. What is the role of perceived risk in the decision process?
|
|
What are some ways to implement your recommendation
: What is the decision facing IMMI?- What factors are important in understanding this decision situation?- What are the alternatives?
|