What is the maximum acceleration from rest of the car

Assignment Help Civil Engineering
Reference no: EM13561466

A car has a 10-ft wheelbase (L). the center of gravity is 18 inches about the ground and 5 ft behind the front axle. The weight of the car is 2500 lb. mechanical efficiency if the drivetrain is 85%. and the wheel radius is 15 inches. The engine of the car develops 200 ft-lb of torque. the overall gear reduction ratio is 8 to 1.

(a) if the car is front-wheel drive. what is the maximum acceleration from rest of the car on good, wet and level pavement?

(b) if the car is rear-wheel drive what is the maximum acceleration from rest of the car on good, dry pavement with a 5% upgrade slope?

Reference no: EM13561466

Questions Cloud

Determine the secondary sludge produced per day per pound : A low rate trickling filter plant gives 95% BOD5 removal. the primary clarifier removes 33% of the BOD5 applied to it. the secondary sludge amounts to 0.029lb dry solid/cap-day. if the raw wastewater has a BOD5 of 0.17lb/cap-day.
Determine the volume of stone required for each filter : A two stage high rate trickling plant is to treat a municipal wastewater having a flow of 2.0mgd. pertinent data: influent BOD5 = 200mg/l, BOD5 removal by primary clarifier = 33%, filter bed depth = 5 to 7ft,
How long until the concentration is reduced : The Fluoride feeder runs out of feed solution. The rapid mix tank is connected to a 5 km long distribution pipe. The flow rate into the tank mix tank is 0.44 m?/s and the volume of the tank is 2.50 m?.
Determine the force supported by the hydraulic cylinder : A Steel plate weighing 205 lb with a center of gravity at point G is supported by a roller at point A,a bar DE, and a horizizontal hydraulic cylinder BC. Negelcting all weights of all members except for the plate,
What is the maximum acceleration from rest of the car : A car has a 10-ft wheelbase (L). the center of gravity is 18 inches about the ground and 5 ft behind the front axle. The weight of the car is 2500 lb. mechanical efficiency if the drivetrain is 85%. and the wheel radius is 15 inches
What is the rolling resistance of the road : A CAT 834H (rubber tires, high pressure), with an operating weight of 103,849 lbs, is pulled up a road whose slope is +3.0% at a uniform speed. If the average tension in the towing cable is 6,060 lb,
How much does the choice of the distribution affect : On a single graph, plot the PDFs if E is assumed to be normally, lognormally, and gamma distributed.  Plot the PDFs for E values between 10,000 and 50,000 kips/in2.  Make sure to label the axes and use a legend to label the curves.
Estimate the electrical power in watts that needs : A small town produces 0.15 MGD of wastewater. How many acres in size would an aerated lagoon need to be to treat this wastewater assuming a depth of 8 ft. and a detention time of 6 days? (7.48 gal/ft^3 ; 43,560 ft^2/acre)
What are the basic assumptions of the traffic flow model : Two 25-kip loads are maintained 6 ft apart as they are moved slowly across the 18-ft beam ab. write a computer program and use it to calculate the bending moment under each load and at the midpoint c of the beam for values of x from 0 to 24 ft at int..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find outlet volumetric flow of toluene from the process

Saturated steam (at 20 bar) is used to heat up a toluene stream from 40oC, 1 bar to 150oC, 1 bar in a heat exchanger. The toluene stream is flowing at a rate of 100 kg/min. Steam leaves the heat exchanger as a saturated liquid at 20 bar.

  Determine what is the maximum column load in kips

What is the maximum column load in kips that could be placed on a 4-ft square temporary footing on a sand for which the standard resistance is about N=15 and the water table is at the surface? A factor of safety of 2 is to be maintained against be..

  Determine the total solids in the sample

A surface water sample has been evaporated until dry in a crucible dish. The dry (tare) weight of the crucible is 44.642gm. The weight of the residue plus the cruciible is 44.6484gm.

  Estimate the required stack height for wind speeds of 4

A plant is to be constructed that will emit 3.5 metric tons of hydrogen sulfide per day. One of the design criteria is that the concentration 1 km downwind from the stack

  Determine the values of x and z for the coordinates of point

If the resultant force is directed along the boom from point A towards O, determine the values of x and z for the coordinates of point C. Set F sub B equal to 1490 N and F sub C equal to 2320 N.

  Calculate the fluid viscosity if the torque on the inner

For two 0.2 m long rotating concentric cylinders, the velocity distribution is given by u(r) = 0.4/r - 1000r m/s. If the diameters are 2 cm and 4 cm, respectively, calculate the fluid viscosity if the torque on the inner cylinder is measured to be 0...

  Find the water depth must be three-quarters of the width

A channel of a rectangular section is to take a certain discharge Q at critical flow; prove that for the wetted perimeter, P=b+2y to be minimum, the water depth must be three-quarters of the width

  Calculate the direct runoff using the scs method

A hyetograph has a uniform rainfall intensity of 1.5 in/hr in the first hour, 2.0 in/hr in the second, and 0.75 in/hr in the third. Calculate the direct runoff (in inches) using the SCS method. Assume a curve number of 65.

  Find the minimum theoretical wall thickness

A flow of 600cfs is measured at a depth of 3.4 ft in trapezoidal channel with bottom width of 25ft and side slopes of 3:1(h:v). The channel reach has a slope of .002. Estimate the channel roughness.

  Determine what is the removal efficiency of the incinerator

A hazardous waste incinerator is to burn 200 Kg/h of PCB waste that is 30 % PCB and 70 % organic solvents. During testing phase, the concentration of PCB in the emission was recorded as 0.025 g/ m³

  What is maximum area of spill in if flashover to be avoided

An industrial building has floor area of 5 m by 8 m and is 3 m high with a door 1 m wide and 2 m high. Leakage of transformer oil from a pump occurs and is ignited. What is the maximum area of spill in (m^2) if flashover is to be avoided.

  Compute detention time and horizontal flow through velocity

Compute the detention time and horizontal flow through velocity. Do these values satisfy the standards for water works, which stipulate detention time is greater and equal to 30 min and 0.5 ft/min =

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd