What is the maximum acceleration from rest for the car

Assignment Help Civil Engineering
Reference no: EM13555026

A newly designed car has a 9.0 ft wheelbase, is rear wheel drive, and has a center of gravity 18 inches above the road and 4.3 ft behind the front axle. the car weighs 2450 lb, the mechanical efficiency of the drivetrain is 90% and the wheel radius is 14 inches. the base engine develops 200 ft-lb of torque, and a modified version of the engine develops 240 ft-lb of torque. if the overall gear reduction ratio is 8 to 1, what is the maximum acceleration from rest for the car with the base engine and for the car with the modified engine?

Reference no: EM13555026

Questions Cloud

What is the maximum speed of the goldfinch : A 30.0- goldfinch lands on a slender branch, where it oscillates up and down with simple harmonic motion of amplitude 3.50×10?2 and period 1.50. What is the maximum speed of the goldfinch
Determine the pressure that develops in the container : A rigid-walled cubical container is completely filled with water at 40 0F and sealed. The water is then heated to 100 0F. Determine the pressure that develops in the container when the water reaches this higher temperature
Draw a mass balance diagram and estimate the monthly mass : Each month the speedy dry Cleaning company buys 1 barrel (0.160 m^3)of dry cleaning fluid . Ninety percent of the fluid is lost to the atmosphere and 10 percent remains as residue to be disposed of
Determine how many rpms is it doing : You rev your car's engine to 2600 (). a) If you change the period of the engine to 0.038 , how many rpms is it doing
What is the maximum acceleration from rest for the car : A newly designed car has a 9.0 ft wheelbase, is rear wheel drive, and has a center of gravity 18 inches above the road and 4.3 ft behind the front axle. the car weighs 2450 lb, the mechanical efficiency of the drivetrain is 90% and the wheel radius i..
What are the recorded values of r dot : At the bottom of a loop in the vertical plane an airplane has a horizontal velocity of 315 mi/h and is speeding up at a rate of of 10ft/s^2. The radius of curvature of the loop is 1mi
What was the students associated perception/ reaction time : An engineering student is driving on a level roadway and sees a construction sign 500 ft ahead in the middle of the roadway. the student strikes the sign at a speed of 25 mi/h.
Compute what is the speed of the bullet before impact : A 0.004-kg bullet is fired into a 0.200-kg block of wood at rest on a horizontal surface. what is the speed of the bullet before impact
Devise an absolute temperature scale where the boiling point : Devise an absolute temperature scale where the boiling point of water at 1 atmosphere (101 kPa) pressure = 100 degrees in your scale What is the ice point of water in your scale?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Estimate total cost and cost per linear foot for furnushing

estimate the total cost and cost per linear foot for furnushing and driving steel-sheet piling for construction of the basement of a building, 150 by 240 ft. the piles will be 22 in. wide, 18 ft. long, and weigh 40.3 Ib/Lin ft.

  Course ab of a five-sided traverse runs due east

Course AB of a five-sided traverse runs due east. From the given balanced interior angles (listed below) to theright, compute and tabulate the bearings and azimuths from northfor each side of the traverse.

  Find where building should be located relative to centreline

A developer has requested permission to build a large retail store at a location adjacent to the intersection of an undivided four-lane major road and a two-lane minor road. Traffic on the minor road is controlled by a stop sign.

  Find shear stress on each bolt and bearing stress on the bar

Due to an error, the length L shown was 1.795 m instead of 1.80 m, thus there is a gap of 0.5 cm, which makes it difficult to bolt the bar on the structure. The engineer suggests the bar is heated up by - Delta in order to close the gap.

  Devise a vertical alignment to connect the tunnel and bridge

An engineering mistake has resulted in the need to connect an already constructed tunnel and bridge with a vertical curve. The profile of the bridge and tunnel is given in the figure below

  Briefly outline with the use of neat labelled sketches

It is proposed to make a new pedestrian access running directly south from University Square to Silvertown. The physical barriers that need to be overcome are the Royal Docks and the City Airport runway.

  Why do owners prefer the design-build form of contracts

Why do owners prefer the design-build form of contracts when many of them know they can obtain better quality construction using other forms. What are the stages at which the designer will schedule design reviews.

  What is time-mean speed and space-mean speed for vehicle

assume you are an observer standing at a point on the track for a period of 30 minutes and are recording the instantaneous speed of each vehicle as it crosses your point. what is the time-mean speed and space-mean speed for these vehicles for this..

  Determine the amount of garbage produced in the city

A city with 28,000 percent population is planning solid waste program. Population growth in the city is estimated to be 2.2% annually and the planning will designed for 30 years, The dumping area is located 20km away from the city.

  Determine corresponding increase in the diameter of vessel

a spherical pressure vessel has an outer diameter of 10 ft and a wall thickness of 0.5 in. knowing that for the steel used ?all= 12 ski, E= 29 x 10^6 psi, and v= 0.29, determine (a) the allowable gage pressure,

  Determine what is the decrease in thickness of the 6-ft fill

A loose, uncompacted sand fill 6 ft in depth has a relative density of 40%. Laboratory tests indicated that the minimum void ratios of the sand are 0.46 and 0.90, respectively. The specific gravity of solids of the sand is 2.65.

  Determine the exit temperature if the gas is argon

A diffuser receives an ideal gas flow at 100 kPa, 300 K with a velocity of 250 m/s and the exit velocity is 25 m/s. Determine the exit temperature if the gas is argon, helium or nitrogen.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd