What is the mass transfer rate on both the top and bottom

Assignment Help Mechanical Engineering
Reference no: EM13642879

Given a flat plate like surface that is 0.1m by 0.25m.

Density of water=1000 kg/m^3

Density of oil =800kg/m^3

And a diffusion coeffiecnt. D(oil->water)= 1*10^-9 m^2/s

If the flat surface is submerged in water and has an oily film covering both surfaces

1. What is the mass transfer rate on both the top and bottom surfaces(kg/s). Are they equal and why?

2.Estimate how long it will take for the oil to disperse from the surfaces given the initial oil layer is 1mm thick?

Reference no: EM13642879

Questions Cloud

A car decelerates uniformly and comes to a stop after 10 s : a car decelerates uniformly and comes to a stop after 10 s. the cars average velocity during deceleration was 50 kmh.
A 53 g sample of impure kclo3 solubility 71 g per 100 g : a 53 g sample of impure kclo3 solubility 7.1 g per 100 g h2o at 20 degrees c is contaminated with 13 percent of kcl
A 040-kg block initially at rest on a frictionless : a 0.40-kg block initially at rest on a frictionless horizontal surface is acted upon by a force of 3.0 n for a distance
You have three 30 uf micro farads capacitors two of the : you have three 3.0 uf micro farads capacitors. two of the capacitors are in parallel and this parallel combination is
What is the mass transfer rate on both the top and bottom : given a flat plate like surface that is 0.1m by 0.25m.density of water1000 kgm3density of oil 800kgm3and a diffusion
Calculate the magnitude of the electric field at one corner : calculate the magnitude of the electric field at one corner of a square 0.990 m on a side if the other three corners
In general ionization energies increase across a period : in general ionization energies increase across a period from left to right. explain why the second ionization energy of
The captain maintains a compass bearing of northwest and a : a small boat is headed for a harbor 35 km directly northwest of its current position when it is suddenly engulfed in
Perform a complete analysis of the cycle to determine the : a power plant operates on an ideal rankine steam cycle using water as the working fluid. the condenser operates at 10

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The potential at location c is 799 v and when released from

the potential at location a is 377 v. a positively charged particle is released there from rest and arrives at

  Develop an equation for the volume of the oil as a function

you are working as a summer intern at a company and a fellow intern obviously an u of a engineering student accidently

  Show that the radial outlet velocity at the impeller tip is

consider a double-sided centrifugal compressor with the following design parametersoutlet diameter of impeller 50

  What is the moment as the bottom of a telegraph pole that

what is the moment as the bottom of a telegraph pole that is 50m high adn 25cm in diameter in a 34ms wind? the

  Assuming no air has leaked into the pan during cooling

a person cooks a meal in a 30-cm-diameter pot that is covered with a well-fitting lid and lets the food cool to the

  The model pump has am impeller diameter of 10 cm and a

a 15 scale model of centrifugal water pump was tested. the model pump has am impeller diameter of 10 cm and a rotation

  If the maximum torsional shear stress is limited to 10ksi

a hollow aluminum shaft is to carry a torque of 200 in.kips. the inner radius is 1in and it is 5ft in length. if the

  What is percentage increase in the force that is required

the hydraulic jack shown below consists of a master cylinder with a diameter of 60mm and a lifting or slave cylinder

  Find the elapsed time to vaporize the propane and total

a factory has a large liquid propane storage tank. the propane is to be used as vapor. evaporation of the liquid

  A loaded railroad car with mass m is rolling at a constant

a loaded railroad car with mass m is rolling at a constant speed v0 when it couples with a massless bumber system.

  For flow over a prescribed geometry what are the

what is the coefficient of friction? the nusselt number? for flow over a prescribed geometry what are the independent

  Calculate the heat emitted to the environment btusec the

a 600 mw coal-fired power plant has an overall thermal efficiency of 38. it is burning coal that has a heating value of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd