What is the mass flow rate of gaseous oxygen

Assignment Help Mechanical Engineering
Reference no: EM13710338

Liquid oxygen (LOX) is used as rocket fuel to launch satellites into space. However, it is easier (and less dangerous) to transport oxygen in gaseous form. What is the mass flow rate of gaseous oxygen that flows at 25 m/s through a 0.5-meter diameter pipe. Assume the temperature of the oxygen is 15 C and that the pipe is pressured to 150 kPa gage. The gas constant of molecular oxygen (O2) is [8.314 J / (K mol)] / (32 g / mol) * (1000 g / kg) = 259.8 J / (K kg).

Reference no: EM13710338

Questions Cloud

What is final temperature and assume process is adiabatic : An evacuated 1-ft3 tank is connected by a valve to a nitrogen supply line flowing air at 120 psi and70oF. A valve is opened allowing air to flow into the tank until the pressure reaches 90 psi. How much mass flowed into the tank and what is its final..
Consider the variation of specific heat with temperature : A gas turbine power plant operating on an ideal Brayton cycle has a pressure ratio of 7. Determine the back work ratio of this cycle, if the temperature of air at the compressor and the turbine inlet are 300 K and 1300 K respectively. (Consider the v..
Determine the radius of curvature of the particle path : A particle which movies in a two-dimensional curvilinear motion has coordinates in millimetres which vary with time t in seconds according to x=5t2 +4 and y=2t3 + 6. For time t =3s, determine the radius of curvature of the particle path and the magni..
Neglect kinetic-potential energy changes-compressor power : Air is compressed at steady state from 100 kPa, 300 K, to 600 kPa, 440 K with a mass flow rate of 4 kg/s. Heat transfer occurs at a rate of 42.3 kJ/kg of air flowing to cooling water circulating in a water jacket enclosing the compressor.
What is the mass flow rate of gaseous oxygen : Liquid oxygen (LOX) is used as rocket fuel to launch satellites into space. However, it is easier (and less dangerous) to transport oxygen in gaseous form. What is the mass flow rate of gaseous oxygen that flows at 25 m/s through a 0.5-meter diameter..
Neglecting heat transfer and potential energy : Steam enters a nozzle at steady state at 20 bar and 280°C, with a velocity of 80 m/s. The exit pressure and temperature are 7 bar and 180°C. Mass flow rate is 1.5 kg/s. Neglecting heat transfer and potential energy. Sketch the process on a T-v diagra..
Calculate product temperature at the center : A cooked mashed potato is cooled on trays in a chilling unit with refrigerated air at 2 C blown over the product surface at high velocity. The depth pf the product is 30mm and the initial temperature is 95 C. The product has a thermal conductivity of..
Allows the user to enter number that represent month of year : Write a program that allows the user to enter a number that represent the month of a year (1 to 12) and uses a switch construct to convert the month number to its corresponding number of days, where January is considered the 1st month of a year and D..
What is the amount of the equal monthly payment : Suppose you take out a car loan of $10,000 with an interest rate of 12% compounded monthly. You will pay off the loan in 48 months with equal monthly payments. What is the monthly interest rate? What is the amount of the equal monthly payment?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Air is adiabatically compressed in a non flow process from

air is adiabatically compressed in a non flow process from a pressure of 14.7 psia and temperature of 70 degrees to 200

  Consider an isentropic expansion process in a piston

consider an isentropic expansion process in a piston cylinder device where air is expanded from 1mpa and 800 k to 0.1

  Calculate an experession in terms of the constants abc and

a cylindrical nuclear fuel rod under steady conditions in a cooling bath has a 2-d temperature distribution of

  The gear is to transmit 90 hp at 300 rpm what does the

aan 8-inch pitch diameter steel gear 3 inches thick face width is pressed onto a 2 inch diameter steel shafte30000000

  The velocity of a particle along the s-axis

The velocity of a particle along the s-axis is given by v = 17s^3/2 where s is in millimetres and v is in millimetres per second. Determine the acceleration when s is 3.3 millimetres.

  The lower plate moves at a constant velocity v while the

a fluid is held between a lower place of temperature t1 and an upper place of temperature t2 the distance between the

  A cylindrical bar of radius 15 mm and length 100 mm is held

a cylindrical bar of radius 15 mm and length 100 mm is held at both ends. if at 30 degc no axial force exists in the

  The energy loss in the system is 25 times the velocity head

the pump is delivering hydraulic oil with a specific gravity of 0.85 at a rate of 20 gallons per minute. the pressure

  Determine the tension in cable and the reaction

A 12-m pole supports a horizontal cable CD and is held by a ball and socket at A and two cables BE and BF. Knowing that the tension in cable CD is kN and assuming that CD is parallel to the x axis (phi = 0), determine the tension in cable BE and BF a..

  A particle which moves with curvilinear motion has

a particle which moves with curvilinear motion has coordinates in meters which vary with time t in seconds according to

  Determine the rate of metal removal

Determine the rate of metal removal when the wheel is engaged in the work and if the number of active grits per square inch = 200, determine the average chip length and the number of chips formed per time

  Determine the distanced s traveled by the 10-kg cart before

the system is released from rest with no slack in the cable and with the spring unstretched. determine the distanced s

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd