User Account

All Pages

What is the magnitude of the instantaneous current at 20usec

Assignment Help Electrical Engineering
Reference no: EM13268648

A charged 100- picoFarad capacitor has initial voltage across it of 10 V. A 100 kohm resistor is suddenly connected across the capacitor (at t=0) to discharge it. What is the magnitude of the instantaneous current at 20 usec?

Reference no: EM13268648

Questions Cloud

What is the mean and the variance of a binomial distribution : The mean and the variance of a binomial distribution with parameters n and theta are 12 and 3. Find the probabilities: a. (P X or equal 7).
Determine at the most one valve is defective : A sample of 16 pvc valves for gas engines is randomly selected from a very large batch, and tested. Let X denote the number of valves out of the 16 selected that are found to be defective when tested. Valves are defective or non-defective independ..
How far away is the mountaintop : You see lightning strike a mountaintop, and 2.98 s later you hear the accompanying thunder. How far away is the mountaintop
Explain what is the molarity of the hydroiodic acid solution : An aqueous solution of hydroiodic acid is standardized by titration with a 0.182 M solution of barium hydroxide. If 17.7 mL of base are required to neutralize 21.9 mL of the acid, what is the molarity of the hydroiodic acid solution
What is the magnitude of the instantaneous current at 20usec : A charged 100- picoFarad capacitor has initial voltage across it of 10 V. A 100 kohm resistor is suddenly connected across the capacitor (at t=0) to discharge it. What is the magnitude of the instantaneous current at 20 usec
Compute the initial molarity of ba(oh)2 : Calculate the initial molarity of Ba(OH)2 and the molarities of Ba2+, OH -, and H3O+ in an aqueous solution that contains 0.70 g of Ba(OH)2 in 0.173 L of solution.
Find the value of a and k for the relative damping ratio : (a) find the value of a and K so that the relative damping ratio of the system is 0.5 and the rise time step response is approximately 1 s. (b) with the values of a and k found in previous question above , find the steady state of the system .
Explain the procedure for conducting a melting point : Describe the procedure for conducting a melting point experiment. Include the names of the equipment used and the observations you could expect to make.
Describe how you can get two different values : You and your lab partner take melting points of the same sample. You observe a melting point of 101-107°C, while your partner observes a value of 110-112°C. Explain how you can get two different values with exactly the same sample.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate the power factor at whic the source operates

In each of the three phases in a balanced delta- connected load is composed of a 10mF capacitor in parellel with a series-connected 470 ohm resistor and 4mH inductor combination, assume a phase voltage of 400 V at 50 Hz

  Calculate the total power in kilowatts

Three series impedances of 33 ohm, 6j ohm and 87j ohm W are connected in star across a 220-V, three-phase supply. Sketch the circuit diagram and the phasor diagram (Take Vab as reference). Calculate the total power in kW.

  What is probability that each of seeds wins championship

We will make the follwoing probability assumptions: When team A plays team B, the probability that team A wins is given by: P(A wins) = \(([seed(B)+3]^2)/([seed(A)+3]^2 +[seed(B)+3]^2) \)

  Find voltage gain for each both as a ratio and in decibels

how the amplifiers should be connected. To proceed, evaluate the two possible connections between source S and load L, namely, SABL and SBAL. Find the voltage gain for each both as a ratio and in decibels. Which amplifier arrangement is best

  Explain how a random variable x is normally distributed

A random variable X is normally distributed with mean u = 10 and standard deviation sigma = 1.5. Find the following probabilities: A. P(8 or equal 8.5).

  Explain briefly why xl limits amount of alternating current

Explain briefly why XL limits the amount of alternating current. Explain why XL increases with higher frequencies and more inductance. How might you use this fact in an application.

  Find what is the largest positive-going noise spike

A certain logic family has the following voltage parameters: VIH(min)=3.5V , VIL(max)=1.0V; VOH(min)=4.9V, VOL(max)=0.1V a) What is the largest positive-going noise spike that can be tolerated

  Calculate amount of blood that has moved through the body

If blood flows at a rate of 5 L/min for 3.5 minutes and then 4.5 L/min for 2 minutes, calculate the amount of blood that has moved through the body over the whole time period.

  Design an 8085 microprocessor system that has a total

Design an 8085 microprocessor system that has a total of 4Kx8 EPROM space using a single 4Kx8 chip and a total of 4Kx8 RAM using two 2Kx8 chips. The EPROM should be mapped starting at address 0000 hex

  What is rms voltage across the primary side of transformer

A) What is the rms current in the circuit B) The primary side of the transformer has 20 times as many turns as the secondary side. What is the rms voltage across the primary side of the transformers

  Explain using the routh hurwitz method

Using the Routh Hurwitz method, find the values of k for which the following polynomial has all its roots to the left of s = -1.

  Define a design of a series controller

Design a series controller (a PD, PI or PID) so that the following performance specifications are satisfied. Steady-state error due to a step input = 0

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd