What is the machines maximum displacement

Assignment Help Mechanical Engineering
Reference no: EM131144163

A machine oscillates in simple harmonic motion and appears to be well modeled by an undamped single-degree-of-freedom oscillation.

Its acceleration is measured to have an amplitude of 10,000 mm/s 2 at 8 Hz. What is the machine's maximum displacement?

Reference no: EM131144163

Questions Cloud

How is the marginal propensity to consume affected : How is the marginal propensity to consume affected? How is the multiplier affected?
Calculate the change in frequency and velocity amplitude : Calculate the change in frequency, velocity amplitude, and acceleration amplitude if the maximum deflection remains 10 cm.
What is the effect on saving of a $1 change in total income : Suppose the consumption function is given by C = a + bYd where a and b are constants (b is the marginal propensity to consume), and Yd is disposable income, equal to Y - T. Taxes vary with income and are equal to t0 + tY where t0 and t are constant..
Prepare an income statement through gross profit : At the end of Duckworth Department Store's fiscal year on November 30, 2010, these accounts appeared in its adjusted trial balance.
What is the machines maximum displacement : Its acceleration is measured to have an amplitude of 10,000 mm/s 2 at 8 Hz. What is the machine's maximum displacement?
Explain in detail the major risks surrounding byod : Analyze in detail the major risks surrounding BYOD, and analyze the security controls and technologies that are currently available and being utilized to manage these risks.
Recalculate the output costs of the recession : Suppose changes in the age structure of the workforce meant that full employment in 2002 was actually associated with an unemployment rate of 4.5 percent rather than the 5 percent figure used earlier. Recalculate the output costs of the recession...
What is its natural frequency : A simple undamped spring-mass system is set into motion from rest by giving it an initial velocity of 100 mm/s. It oscillates with a maximum amplitude of 10 mm. What is its natural frequency?
Enter the beginning balances in the ledger accounts : Enter the beginning balances in the ledger accounts and post the April transactions. (Use J1 for the journal reference.)

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Herzberg specifically classed salary as a hygiene factor

herzberg specifically classed salary as a hygiene factor not a motivator. how does salary fit in with maslows

  When x 10 ft the crate has a speed of 20 fts which

when x 10 ft the crate has a speed of 20 fts which increasing at 6 fts2. determine the dirction of the crates velocity

  If the convective heat transfer coefficient is 135 w m2k

a long beer can made of thin a1 sheet l 1 cm k 205 wmk is removed from refrigerator and set on a table air temp

  Determine the acceleration of the mass center of the disk

a 4-in. diameter disk shown weigts 20 lb. the disk is released at rest when theta30 degrees and rolls down the curved

  What is the correct decimal notation for the number

What is the correct decimal notation for the number 1.345 x 10-1?

  Draw the qualitative influence line for the moment at b

Draw a qualitative influence line for the reaction at support A for the beam - Draw the qualitative influence line for the moment at B.

  Heat transfer occurs at a rate of 2 kw from the compressor

air enters a compersoor operating at steady state at 1.05 bar 300k with a volumetric flow rate of 12 m3min and exits at

  Find the net upward force on the inflated balloon

A rubber balloon has a mass of 1500 g when it is deflated, i.e., empty. When the balloon is filled up with Helium gas (He = 0.18 kg/m3 ), it takes the form of a sphere with a 4 m diameter. (V-sphere= (4/3)(pi)(r)^3) Find the net upward force on the i..

  Assuming constant specific heat at room temperature

A Stirling cycle operates with 1 kg of air between thermal energy reservoirs at 27oC and 527oC. The maximum cycle pressure is 2000 kPa and the minimum is 100 kPa. Assuming constant specific heat at room temperature,

  Find the temperature at the interface

a. Find the temperature at the interface between the rod and sleeve and on the outer surface. b. What is the temperature at the center of the rod?

  Locale the critical points of fxy x3 y3 3xy 5 and

use the chain rule to find and where z arcsin 2x - y and x .s2 t2 y 1 - 3 st. let fus t vs t where f u and v are

  Now we have to find a new material so he can spin the ball

a man tried spinning a ball round and round in the air at the end of a unknown material its a rope like structure but

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd