What is the longest amount of time that particle can take

Assignment Help Civil Engineering
Reference no: EM13313650

A particle enters a 20 meter long rectangular settling tank an travels with the flow at a horizontal velocity of 0.09 meters per second. If the tank is 2 meters deep and the particle enters the tank at the surface of the water, what is the longest amount of time that the particle can take to settle, if it is to be removed?

Reference no: EM13313650

Questions Cloud

Influence of social and perception of social media : The influence of social and perception of social media by Turkish travel media when they are engaged with British female travellers
What is the probability : The probability that a student passes a written test for a private pilot's license is 0.75. What is the probability that a student will fail the test on the first attempt and pass it on the second attempt?
Calculate the area of reinforcement required : A short Reinforced Concrete column is 300mm x 400mm. It is required to carry an ultimate load of 1500kN and an ultimate major axis bending moment of 300kNm. Calculate the area of reinforcement required.
Find the batterys internal resistance : A battery has an emf and an internal resistance . When the battery is connected to a 25 ohm resistor, the current through the battery is 0.65 A. Find the battery's internal resistance
What is the longest amount of time that particle can take : If the tank is 2 meters deep and the particle enters the tank at the surface of the water, what is the longest amount of time that the particle can take to settle, if it is to be removed
Explain what is the ph of the resulting solution : A solution was prepared by mixing 0.01150 HA and 0.01150 mol of NaA in a 500 ml Volumetric flask and diluting to mark. What is the pH of the resulting solution
Calculate how much bod is remaining after 12 days : A 250 cubic meter reaction tank contains a waste water having an ultimate BOD concentration of 755 mg/L. If the BOD reaction rate constant is -0.352/day, how much BOD is remaining after 12.0 days
Compute the new partial pressures after equilibrium : After a quantity of NO2(g) is injected into the mixture, the total pressure jumps to 812 torr. Calculate the new partial pressures after equilibrium is re- established.
What is the work done by this force on the truck : The brakes of a truck cause it to slow down by applying a retarding force of 7710 N to the truck over a distance of 1050 m. What is the work done by this force on the truck

Reviews

Write a Review

Civil Engineering Questions & Answers

  Environmental impact regarding the construction of the dam

Draw A flow net. Show flow lines, flow Channels, and Equipotential lines. Using flow nets, please provide an estimate of seepage rate below the dam. Your submittal will provide the basis for an environmental impact statement regarding the construc..

  What are pressure heads at the interface and at the bottom

A stratified lake could be idealized as two layers: with 7.0 m of fresh water on top and 10.0 m of cold water (specific gravity = 1.02) on the bottom. What are the pressure heads at the interface and at the bottom of the lake, in terms of water col..

  Determine the height of the weir for discharge coefficient

This weir is to be replaced by an uncontracted horizontal weir that will maintain the same upstream depth. Determine the height of the weir if the discharge coefficient is based on the following equation: C = 1.78 * 0.22(H/p)

  What is the distiniction b/n point and non point sources

what is the distiniction b/n point and non point sources of water pollution and thier varation with surface and ground water?

  Write a paper on steel sustainability

Write a paper on steel sustainability.

  Geometric design and construction of a new two-lane road

Geometric design and construction of a new two-lane two-way road has been recently completed and now it is time for design pavement near Ballarat, Victoria.

  Determine the rainfall excesses for successive periods

Assume a saturated hydraulic conductivity of 0.8 in./hr, a porosity of 0.62, an initial moisture content of 0.28, and an average capillary suction of 7.2 in. The depression storage is 0.5 in.

  Determine the required source temperature of heat sink

A Carnot heat engine is supplied with a high temperature heat source at a rate of 200 kW. If the power output of the heat engine is 120 kW, determine the required source temperature if the heat sink temperature is 20 °C.

  Calculate capillary pressure for the inner capillary tube

Two glass capillary tubes of inside diameters of 20 and 13 microns are used to test the capillary rise in an annular cross section .The wall thickness of each capillary is 2 microns .The smaller capillary tube is inserted in the larger one so that..

  Determine what is the angular rotation rate of the car

A car is travleing towars a 20 degree slope at 60 mph. The wheels have a radius of 12 in. and the car's wheelbase is 100 in. What is the angular rotation rate of the car immediately after the front wheel contacts the slop

  What are the basic assumptions of the traffic flow model

What are the basic assumptions of the 'traffic flow model' and 'capacity model' used in signal timing design. Discuss.

  What is bulk modulus of a liquid that has a density increase

What is the bulk modulus of a liquid that has a density increase of 0.02 percent for a pressure increase of 1000 lb/ft^2

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd