What is the left turn adjustment factor for the case describ

Assignment Help Civil Engineering
Reference no: EM13543434

An intersection approach has three lanes, permitted left turns, and 6% left-turning volume with a through vehicle equivalent of 5.0 tvu/left turn. The saturation flow rate for through vehicles under prevailing conditions is 1,700 veh/hg/ln.

a. What is the left turn adjustment factor for the case described?

b. Determine the saturation flow rate and saturation headway for the approach, including the impact of left-turning vehicles.

c. If the approach in question has an effective green time of 45 seconds in a 75-second cycle, what is the capacity of the approach in veh/h?

Reference no: EM13543434

Questions Cloud

Provide the velocity distribution for steady flow case : An infinite, long, solid, vertical cylinder of radius R is located in infinite mass of compressible liquid. Provide the velocity distribution for steady flow case
Determine the normal stress in each rod. show all work : Two steel rods with fixed supports at A and C are attached by a rigid flange at point B and a downward load of 120 kN is applied to the flange. The upper rod has a cross section of 800 mm^2 and the lower rod has
Determine the minimum diameter shaft that can be used : The electric motor at A exerts a torque of 800N.m on the steel shaft from A to D. This has a torque of -300N.m at B and -500N.m at C. the dimensions are
Why does a design engineer need to know the location of the : Course Ab of a five sided traverse runs due north. From the giben balanced interior angles to the right, compute and tabulate the bearings and azimuths from north for each side of the traverses.
What is the left turn adjustment factor for the case describ : An intersection approach has three lanes, permitted left turns, and 6% left-turning volume with a through vehicle equivalent of 5.0 tvu/left turn. The saturation flow rate for through vehicles under prevailing conditions is 1,700 veh/hg/ln.
Determine the vertical deflection at c : The bent road has an E=200 GPa, G=75 GPa, and a radius of 30 mm. Use Castigliano's theorem and determine the vertical deflection at C. Include the effects of bending, shear, and torsional strain energy.
Determine the power that must be supplied to the pump at : Crude oil flows through a level section of the Alaskan pipeline at a rate of 1.6 million barrels per day (1 barrels=42 US gallons) the pipe inside diameter is 48 inch and its roughness is equivalent to galvanized iron.
What is the flow rate of air that must be entering the hood : We have a situation where hydrogen gas at 300 degrees C is flowing out of a tube at the rate of 100 mL/min. The tube is located in a fume hood operating at 25 degrees C and 1 atm.
Calculate the potential methane production in one year for : A 9,000-lb single wheel load is placed on a PCC slab that is 9.5 in. thick. The concrete has a modulus of elasticity of 5 million psi with a Poisson’s ratio of 0.15. The modulus of subgrade reaction is 225 pci. Tire pressure is 90 psi.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the magnitude of f2 which will cause the reaction

Determine the magnitude of F2 which will cause the reaction Cy at the bearing C to beequal to zero. The bearings are in proper alignment and exertonly force reactions on the rod. Set F1 = 550 lb.

  Determine the maximum velocity that the skier will achieve

A person with a mass of 200kg wearing snow skis is gliding down a long slope at an angle of 20 degrees. Each ski is 200cm long and 5 cm wide. The pressure of the skis on the snow melts a thin layer of water so that a

  Find the absolute-gage and vacuum pressure heads

A glass jar is heated in an oven and sealed when the air pressure is 103 kPa and the temperature is 105 C. Find the absolute, gage, and vacuum pressures in the jar when it cools to 20 C.

  Write the general mass balance equation for the rinse tank

To remove the solution containing metal from a part after plating the part is commonly rinsed with water. The rinse water is contaminated with metal and must be treated before discharge. The Shiny Metal Plating Co. The plating solution contains 85..

  What will be the new exponent of the blasius equation

The relative roughness ofa pipe is 0.0005, if the blasius equation is applicable for Thecflow Reynolds number above 2700 rather then 3000

  Magnitudes of fac and fad

The 70 m tall tower is supported by three cables that exert forces FAB, FAC, and FAD on it. The magnitude of the force FAB is 2 kN. The x and z components of the vector sum of the forces exerted on the tower by the three cables are zero. What are ..

  How much money will be saved in energy each year

An electric water heater held at 140 °F is kept in a 70 °F room. When purchased, its insulation is equivalent to R-5. An owner puts a 25-ft2 blanket on the water heater, raising its total R value to 15

  What should be thickness of the confined aquifer for strata

The first stratum is confined, and the second one is unconfined, and the water surface elevations in the channels are 24 m and 16 m above the bottom of the unconfined aquifer.

  Repeat the above for all elements in are membering

For this problem you will write a function that calculates avalue between zero and one for each element in a 512x512 matrix(yes thats 512x512).

  What rate of return would it have to make on the basis of si

Farah Manufacturing wants it's investments to double in value in 4 years, what rate of return would it have to make on the basis of (a) simple interest (b) compound interest

  What percentage of water evaporate during throttling process

Saturated liquid water at 1.0 MPa is throttled adiabatically to a pressure of 0.4 MPa. If the change is kinetic energy is negligible, what percentage of the water evaporates during this throttling process

  Determine the time at which the pressure in the tank

The velocity out of the tube may be approximated by V = √(2(p-patm)/ρ), where p is the absolute tank pressure. Determine the time at which the pressure (gage) in the tank is 20 kPa if the initial pressure is 40 kPa (gage)

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd