Reference no: EM13706636
Consider the first order system: y_dot + y = u where y is the output and u is the input,
a) Plot the frequency response curves in Matlab using the analytic functions for the amplitude ratio and phase as a function of w.
b) Plot the frequency response curves in Matlab using bode command and compare the results with part a
c) Derive the total response due to u = sin (10 t)
d) Plot the total response as a function of time.
e) Determine the corner frequency using bode plot. What is the interpretation of this corner frequency?
f) Describe the difference between the total response and the frequency response.
g) Draw the transfer function of the system in a form of block diagrams using a unity feedback configuration.
h) Determine the unit step, unit impulse and unit ramp response of the system analytically and plot the results in Matlab.
i) Plot the unit step, unit ramp and also response due to u = sin (10 t) using SIMULINK.
j) Give an example of a physical system (except an electrical circuit) that has a similar 1st order dynamics as above.
|
Manufacturer claims the average velocity of air leaving fan
: A fan with a diameter of 12 inches operates at a voltage of 120V with a current draw of 0.5 amps. The manufacturer claims the average velocity of air leaving the fan is 33.1 ft./s under standard conditions. Standard air has a density of 0.075 lb mass..
|
|
Compressor with an internal energy
: Saturated steam at 230 degrees F, 20.78 psia and 19.386 ft cubed per pound of mass enters a compressor with an internal energy of 108.26 Btu/lb of mass and is compressed to 80 psia. the mass flow rate is 50 lb mass per hour. Heat loss from the compre..
|
|
Initial and final temperature of liquid due to heat transfer
: A 50 kg hot iron block is dropped into a relatively cold lake at temperature T. During thermal equilibrium the lake receives Q amount of heat from the iron block. Show that the entropy change of the lake is Q/T starting with an expression for the spe..
|
|
Work required using the saturated liquid approximation
: Saturated liquid water at 25 degrees C is pumped to a pressure of 5 MPa in an isothermal process. The specific work required by the pump to pressurize the water to 5 MPa can be found as the change in enthalpy of the water from the inlet pressure to t..
|
|
What is the interpretation of this corner frequency
: Consider the first order system: y_dot + y = u where y is the output and u is the input, Plot the frequency response curves in Matlab using the analytic functions for the amplitude ratio and phase as a function of w. Plot the frequency response curve..
|
|
Temperature of the atmosphere varies with height
: Using the hydrostatic law dp/dz = -(rho)g and the ideal gas law p = (rho)RT, show that if the temperature of the atmosphere varies with height as T(z) = T_o - Bz, then the atmospheric pressure varies with height as p(z) = p_o(1-(Bz/T_o))^(g/(BR))
|
|
Maximum deformation in the rod must not exceed
: A solid 0.625-in. diameter steel [E = 29300 ksi] rod (1) supports beam AB, as shown. If the stress in the rod must not exceed 20 ksi and the maximum deformation in the rod must not exceed 0.26 in., determine the maximum load P that may be supported.
|
|
Saturated liquid vapor mixture of water
: 0.65m^3 rigid vessel initially contains saturated liquid vapor mixture of water at 150C. The water is now heated until it reaches the critical state. Determine the mass of the liquid water and the volume occupied the liquid at the initial state.
|
|
Determine the phase or phases in a system consisting
: Determine the phase or phases in a system consisting of h20 at the following conditions and sketch p-v and t-v diagrams showing the location of each state (a)p=100 lbf/in^2, T=327.86F (b)p= 100lbf/in^2, T240F. (c)T=212F, p=10lbf/in^2 (d)T=70F, p=20lb..
|