Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
a) The input signal to an amplifier is -20 dBm. What is the input signal power in mW?
10 uW
0.01 mW
0.1 mW
100 mW
b) If the input noise power is 1uW, then what is the input noise power in dBm?"
-30 dBm
30 dBm
0 dBm
0.06 dBm
c) Given the input signal and noise power in parts (a) and (b), what is the input signal-to-noise ratio in dB?"
10 dB
-10 dB
-35.56 dB
35.56 dB
d) If the power gain of the amplifier is 115, then what is the power gain in dB?"
40.61 dB
47.45 dB
20.61 dB
94.90 dB
e) If the power gain of the amplifier is as given in part (d), then what is the output signal power in dBm?"
-29.39 dBm
27.45 dBm
0.61 dBm
74.90 dBm
f) If the amplifier contributes 0.01mW of noise power, then what is the output signal-to-noise ratio in dB?"
40 dB
9.64 dB
27.45 dB
0.61 dB
g) What is the noise factor of this amplifier?
1.04
1.05
1.09
1.08
h) What is the noise figure of this amplifier?
0.5 dB
0.36 dB
1.04 dB1.1 dB
Design a circuit that, given a 2-bit value, will light a LED corresponding to that value. One of four LEDs should be lit for each of the four possible input values (binary 0 through 3).
Compute the power absorbed by an element in a circuit, but for a simple sinusoidal current i = sin(2πt/T) where T = 1 s.
Make sure to mark significant points in your figure (amplitude, offset, time, etc.). How could a device be modified to work as an electro-optic phase modulator? If we apply signal V, what is the range of phase shifts induced by this modulator.
A star-bus hybrid topology consists of a main three branch star toplogy with each branch connecting three stations in a bus topology. This toplogy is changed to a new bus-ring hybrid topology with main five station bus topology.
Design a combinational circuit with four inputs, x,y,w, and z, and four outputs: A, B, C, and D. When the binary input value in decimal is 3,8,12 or 15, the binary output value is one less than the input value, otherwise it is one greater than the..
A piece of germanium doped with 1016 cm-3 shallow donors is illuminated with light generating 1015 cm-3 excess electrons and holes. Calculate the quasi-Fermi energies relative to the intrinsic energy and compare it to the Fermi energy in the absen..
Determine the minimum bandwidth, baud, and bandwidth efficiency for the following bit rates and modulation schemes - 8-QAM and 16-QAM. Fb = 2400 bps Fb = 4800 bps Fb = 9600 bps
In code warrior, write a program sequence that places the value in Address $1500 into Accumulator A. Then, AND this value with the value in Address $1501. Save the result in $1502.
S = {c(k + jl) | k = 3, 1, 1, 3 and l = 3, 1, 1, 3 and j = square root of -1, where c is a constant. Determine the value of c to ensure a unit energy constellation. Sketch this constellation. Find d^2 min and label the constellation points with bi..
Which of the following items is considered as a factor of production and which is considered as a raw material? In case you classify an item as a factor of production, identify the type of the resource.
A delta-wye connected three-phase transformer is rated at 38 MVA with primary and secondary line voltage ratings of 345 and 125 kV, respectively. The transformer p.u. reactance is 10%, the p.u. no-load current is 0.1.
A single-phase, half-wave SCR circuit is used to control the power consumption of an inductive load. The resistive component of the load is 5 Ohm. The source voltage is 120 V (rms). When the triggering angle is adjusted to 60 degrees
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd