What is the initial volumetric flow rate of water out of

Assignment Help Mechanical Engineering
Reference no: EM13630168

A garden hose is open at one end and capped closed at the other. A swimmer in an above-ground pool fills the hose with pool water, then throws the capped end out of the pool. The open end of the hose sits at the bottom of the pool, and the capped end sits on the ground outside the pool and level to the bottom of it. The external pressure is 1 atm. The water in the pool is 2.5 feet deep, and the rim of the pool is 3.5 feet above the ground. The pressure at the capped end of the hose is 1.07 atm. Suppose the cap is removed.

a) What is the initial velocity of the water draining out of the hose in ft/s?

b) What is the initial volumetric flow rate of water out of the hose, in gpm (gallons per minute)? You can assume that the inside diameter of the hose is 5/8 inch.

Reference no: EM13630168

Questions Cloud

List ho and ha note remember you are not testing the mean : a state school administrator says that the standard deviation of test scores for eighth grade students who took a u.s.
A 4000 lbf conventionsl vehicle gets 19 mpg a 4000 lbf : a 4000 lbf conventionsl vehicle gets 19 mpg. a 4000 lbf hybrid gets 31 mpg. all other things being equal maintenance
The pressure in the pipe is 100 kpa heat transfer from the : a well known architect designed a 1600 m tall building. in the building steam for the heating system enters at ground
State whether the standardized test statistic x2 allows you : find the critical values for the indicated test for a population variance sample size n and the level of significance
What is the initial volumetric flow rate of water out of : a garden hose is open at one end and capped closed at the other. a swimmer in an above-ground pool fills the hose with
The rotational inertia of a cube is ic 16mcs2 where mc : in the experiment you will study an oscillator called a torsion pendulum. in this case the restoring force is the
With a constant velocity of 120 ms due to a horrizontal : a 10-kg block is moving down along a plane incline at a 10 degree angle. the coefficient of kinetic friction between
A steel bar 2-meters long and having a square : a steel bar 2-meters long and having a square cross-section 2-cm on an edge is pulled in tension with a load of 100000
How much heat in kj must be added to 2 kg of steam : how much heat in kj must be added to 2 kg of steam initially at t1 300 degree c contained within a rigid volume to

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd