What is the initial rate of mass loss of hydrogen by

Assignment Help Mechanical Engineering
Reference no: EM13619777

Gaseous hydrogen at 10 bars and 27C is stored in a 100-mm-diameter spherical tank having a steel wall 2mm thick. THe molar concentration of hydrogen in the steel is 1.50kmol/m^3 at the inner surface and negligible at the outer surface, while the diffusion coefficient of hydrogen in stell is appoximately 0.3 x 10^-12 m^2/s. What is the initial rate of mass loss of hydrogen by diffusion through the tank wall? What is the initial rate of pressure drop within the tank?

Reference no: EM13619777

Questions Cloud

The amount of charge that is induced to flow around the : a conducting coil of 2200 turns is connected to a galvanometer and the total resistance of the circuit is 40 ?. the
Your job pays you only once a year for all the work you did : your job pays you only once a year for all the work you did over the previous 12 months. today december 31 you just
What is the minimum plate length that should be used at : a fan that can provide air speeds up to 50ms is to be used in a low-speed wind tunnel with atmospheric air at 25 degc.
If the western shoreline is horizontally d2 240 m from the : an enemy ship is on the east side of a mountain island as shown in the figure. the enemy ship has maneuvered to within
What is the initial rate of mass loss of hydrogen by : gaseous hydrogen at 10 bars and 27c is stored in a 100-mm-diameter spherical tank having a steel wall 2mm thick. the
How much energy is lost due to friction during the water : a 16.0-kg enters a water slide that has a entrance 2.50 m above the ground exit. when the child exits her speed is 3.50
If the member is 1mm thick and the binary diffusion : a thin plastic membrane is used to separate helium from a gas stream. under steady-state conditions the concentration
What percentage of the value of the firm under policy ii is : a firm earns 1 million in year 0. thereafter it continues to earn 1 million a year in perpetuity. the financial manager
Yourco needs to raise 45000000 by selling bonds no internal : yourco needs to raise 45000000 by selling bonds no internal equity will be generated and yourco has a target capital

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd