What is the initial pressure of the gas what is the final

Assignment Help Mechanical Engineering
Reference no: EM13627643

1 kmol of N2 gas (ideal) is contained in a piston initially at 300K with a volume of 0.1 m^3. The piston cylinder is well insulated. A microwave gun then heats the gas for 30 seconds, where the poser of the microwave gun is 10 MW and the absortion coefficient of the gas is sigma= 0.1. During the microwave heating the N2 gas expands at a constant pressure.

a.) What is the initial pressure of the gas?

b.) What is the final temperature of the gas assuming the heat capacity is a constant?

c.) What is the final temperature from the change in enthalpy?

d.) What is the volume of the gas after heating?

e.) What is the change in entropy using the 1st TdS Relation? assuming Cv(T)=Cv(T1)

f.) What is the change in entropy using the 2nd TdS Relation? assuming Cp(T)=Cp(T1)

g.) What is the change in entropy using the 2nd TdS Relation? assuming Cp(T)=(Cp(T1)+Cp(T2))/2

h.) What is the change in entropy using the 2nd TdS Relation? using Ss and S1

i.) What is the work done by the gas?

Reference no: EM13627643

Questions Cloud

An lr circuit has a resistance r 25 w an inductance l 54 : an lr circuit has a resistance r 25 w an inductance l 5.4 mh and a battery of emf 9.0 v. how much energy is stored
What is the initial pressure of the gas what is the final : 1 kmol of n2 gas ideal is contained in a piston initially at 300k with a volume of 0.1 m3. the piston cylinder is well
Air enters a gas turbine with two stages of compression and : air enters a gas turbine with two stages of compression and two stages of expansion at 100 kpa and 17 degrees celcius.
What is the shape meanexpected value and standard deviation : according to an irs study it takes a mean time of 330 minutes for taxpayers to prepare copy and electronically transfer
What is the initial pressure of the gas what is the final : 1 kmol of n2 gas ideal is contained in a piston initially at 300k with a volume of 0.1 m3. the piston cylinder is well
A hollow metal cube with sides 100mm floats at the : a hollow metal cube with sides 100mm floats at the interface between a layer of water and a layer of sae 10w oil such
The current in an rl circuit is zero at time t 0 and : the current in an rl circuit is zero at time t 0 and increases to 75 of its final value in 4.5 s. the time constant of
What is the shape meanexpected value and standard deviation : according to an irs study it takes a mean time of 330 minutes for taxpayers to prepare copy and electronically transfer
A steel plant heat treats steel rods by passing them : a steel plant heat treats steel rods by passing them through a 1000 degrees c oven. the steel rods are 3 meters in

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd