What is the highest possible design speed for this curve

Assignment Help Civil Engineering
Reference no: EM13556976

You are asked to design a horizontal curve for a two-lane road. The road has 12-ft. lanes. Due to expansive excavation, it is determined that a maximum of 34 ft. can be cleared from the road's centerline toward the inside lane to provide for stopping sight distance. Also, local guidelines dictate a maximum super elevation of .08 ft/ft. What is the highest possible design speed for this curve?

Reference no: EM13556976

Questions Cloud

Does the density or specific weight of the water factor into : Assuming no friction losses in the hose, will the velocity change if the hose is draped over the handrail going around the pool instead of going under it?
Is change in z dependent upon the specific weight or density : If a large pool of water was rotating the same speed as an amusement ride, how far would the surface of the water rise, between the where the chairs are hanging when the ride stopped- which is 15ft from the center support column, and where the chairs..
A man says that the oil was reduced at a rate : An oil storage area abandoned 19 yrs ago had oil spilled on the ground and saturated the soil at a concentration of 400mg/kg of soil. A recent soil sample shows a concentration of 20mg/kg
Determine the emf induced in the second coil : A 2.64m -long coil containing 225 loops is wound on an iron core (average \mu = 1850\mu _0) along with a second coil of 115 loops. Determine the emf induced in the second coil
What is the highest possible design speed for this curve : You are asked to design a horizontal curve for a two-lane road. The road has 12-ft. lanes. Due to expansive excavation, it is determined that a maximum of 34 ft. can be cleared from the road's centerline toward the inside
Calculate the coefficient of permeability : A permeability test was run on a cylindrical soil sample with a length of 175 mm, and a diameter of 75 mm. After 90 seconds, discharge was 300 cm3 under constant head of 41 cm. The sample had a dry mass of 850 g and its ?s was 2.60 g/cm3. Calculate (..
What is the effective nuclear charge experienced : The energy for the 5P valence electron in indium (Z=49) is -5.79 electron volts. What is the effective nuclear charge experienced by this electron
Friction on the concrete surface creates a couple moment : Friction on the concrete surface creates a couple moment of 100 Mm on the blades of the trowel. Determines the magnitude of the resultant couple forces so that the resultant couple on the trowel is zero.
What is the percent change in the area of the glass : A window pane of dimensions 0.75 m x 0.65 m is installed on a day when the temperature is 35F. What is the percent change in the area of the glass

Reviews

Write a Review

Civil Engineering Questions & Answers

  Where to locate the mass center of the assembly

The two upper lengths of the welded Y-shaped assembly of uniform slender rods have a mass per unit length of 0.3 kg/m, while the lower length has a mass of 0.7 kg/m. Locate the mass center of the assembly. lenghts of all rods aew 30mm

  Find the slope necessary to sustain a uniform flow

A flow of 90 cfs is carried in a rectangular channel 10ft wide at a depth of 1.6 ft. If the channel is made of smooth concrete (n=0.016), find the slope necessary to sustain a uniform flow at this depth.

  Determine the time it takes the block to reach position b on

A beam with a 20 ft simple span has cross- section dimentions b= 12" d=12 in and h=25in . it carries a uniform service load of 2450 lb/ft in addition to its own weight. material strengths are f'c=4000psi and fy=60000psi .assume a weight od 150 pcf fo..

  Estimate the coefficient of permeability for a uniform sand

A grain-size analysis for a uniform sand in a loose state indicated that the soil particle diameter corresponding to 10% passing on the grain-size distribution curve is 0.18 mm. Estimate the coefficient of permeability.

  Does surface energy increase or decrease in planar density

The surface energy of a single crystal depends on crystallographic orientation. Does this surface energy increase or decrease with an increase in planar density

  What is the minimum required diameter d of the base plate

A steel circular hollow cylinder is supported on a circular steel plate.This arrangement is supported on a concrete pedestal. The column has outside diameter d = 250 mm and supports a axial load P = 750 kN.

  Determining the pumping rate

Determine the required pumping rate. the aquifer has T= 1600 m 2 /day and the wells each have radius of influence of 600m.

  What is the probability that it will be found by inspect

Items are inspected for flaws by two quality inspectors. If a flaw is present, it will be detected by the first inspector with probability 0.9, and by the second inspector with probability 0.7. Assume the inspectors function independently.

  Net external forces acting upon a particle or rigid body

A condition where there are no net external forces acting upon a particle or rigid body and the body remains at rest. ... forces acting upon a particle or rigid body and the body remains at rest or continues at a constant velocity.

  Maximum height of its centre of gravity

If a mass of 500kg is placed centrally on the top face of the buoy, find the maximum height of its centre of gravity above the bottom of the buoy so that the buoy may remain in stable equilibrium.

  Calculate the volume of the tank in gallons

A cubic shape tank has the dimensions of 10 m by 10 m by 20 m tall. Calculate the volume of he tank in gallons

  How to use the bisection method on the vander wals

How to use the bisection method on the van der waals equation Problem The van der Waals equation gives a relationship between the pressure P (in atm.),

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd