What is the head loss in m

Assignment Help Mechanical Engineering
Reference no: EM13212490

Drinking water at 10oC for an office complex must be pumped along a horizontal section of PVC pipe 50 m long at 2 m/s. The pipe has a nominal diameter of 62.5 mm and is Schedule 40. What is the head loss in m?

Reference no: EM13212490

Questions Cloud

Sketch the cycle on p-v coordinates : One kilogram of air as an ideal gas executes a Carnot power cycle having a thermal efficiency 50%. The heat transfer to the air during isothermal expansion is 50 kJ. At the end of the isothermal expansion, the pressure is 574 kPa and the volume is..
Compute the ph change that takes place : calculate the pH change that takes place when a 100mL of (a) 0.0500M NaOH and (b) 0.0500M HCl is added to 400mL of a buffer solution prepared by mixing 0.200M NH3
What is the electrical power available : You are designing a remote-area power supply based on a miniature wind turbine that is 20% efficient. Meteorological data indicates an average wind speed of 24 km/h at an air temperature of 10oC and pressure of 0.9 atm. The rotor has a diameter of..
Compute the amount of energy in the form of heat : Calculate the amount of energy in the form of heat that is produced when a volume of 1.25 L of SO2(g) is converted to 1.25 L of SO3(g) according to this process at a constant pressure and temperature of 1.00 atm and 25.0 °C. Assume ideal gas behav..
What is the head loss in m : Drinking water at 10oC for an office complex must be pumped along a horizontal section of PVC pipe 50 m long at 2 m/s. The pipe has a nominal diameter of 62.5 mm and is Schedule 40. What is the head loss in m?
Write a brief memorandum to the tax files : Write a brief memorandum to the tax files that summarizes the advice you should give Ron - you notice that Ron has not reported any part of the award as income and has included the medical expenses in computing his itemized deductions.
Find the volume of the ring-shaped solid that remains : A cylindrical drill with radius r1 is used to bore vertically a hole through the centre of a sphere of radius r2.
What is the probability that would find a sample proportion : A sample of 500 business professionals found that 30% chose an airline based on price. If the population proportion of all business professionals who select an airline based on price is .27 What is the probability
Draw and label a process flowchart : Propane gas enters a continuous adiabatic heat exchanger' at 40°C and 250 kPa and exits at 240°C superheated steam at 300°C and 5.0 bar enters the exchanger flowing counter currently to the propane and exits as a saturated liquid at the same press..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the natural frequencies of the system

Determine the natural frequencies of the system. For the baseline system I get natural frequencies at the following engine speeds: 435, 2026, 2818, 5225, 7093, 10245, and 12153 rpm.

  Newtons laws describing equations of motion

Newtons laws describing equations of motion for balance beam with cart (ball), Need to obtain a working mathematical model of the balance beam problem, preferably with a cart, not a ball

  Find out the exit temperature

Determining the Exit Temperature and Power Input of Air through a Compressor, Air at 150Pa and 310K enters a compressor of inlet diameter 2cm. The Compressor raises the pressure to 3.5 times the inlet pressure

  Find the maximum load on bevel gear and shaft

You have a bevel gear and shaft and you have to find the maximum load that can be applied on it.

  Calculate the mass of steam in the vessel

A rigid vessel of capacity 0.6 m3 contains dry saturated steam at 4.0 bar. The vessel is cooled until the pressure is reduced to 2.0 bar, Calculate; a) the mass of steam in the vessel.

  Measurements of the load required to propagate a crack

SEM212 - Aim of this demonstration is to use measurements of the load required to propagate a crack (tear) in packaging tape to determine its fracture toughness.

  Find the temperature of source and sink

a heat engine working on carnot cycle converts 25% of heat into work when the temperature of the sink is reduced by 353 k the efficiency gets doubled .find the temperature of source and sink.

  Explain what will the ratio of the angle of twist

What will the ratio of the angle of twist be to that of the hollow shaft if the maximum shear stress in the material of 75 N / mm ^2 and what is the ratio of actual permissible shear stress?

  Determine metal removal rate

Determine metal removal rate, etching time, and required dimensions of the opening in the cut and peel maskant required to achieve the desired pocket size on the part.

  Compute the power required to overcome the skin

Calculate the power required to overcome the skin friction drag on the keel of a sailing dingy moving through water at 2m/s. The keel projects 0.8m into the water and it is 0.4m wide

  Compute the maximum bending stress at mid-span

Calculate the maximum bending stress at mid-span, and, for the same section, locate the neutral axis. Neglect the weight of the beam

  Explain the velocity of the ball when it reaches the highest

A ball with a mass of 0.25 kg is thrown vertically upward with an initial velocity of 10 m/s. What is the velocity of the ball when it reaches the highest point?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd