Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Lets' try this again.
Vin= 1V
Vout=1.99V
Freguency = 100 hZ
R=330 Ohms
C= 0.47 uF
What is the Gain dB?
I thought dB=20 log (Vout/Vin) This would lead me to believe that it should be 20 log (1.99/1) = 5.98 dB...I am being told the answer is -0.44 dB. What is my problem
A 50-KVA, 13,800/208 V ?-Y distribution transformer has an equivalent phase impedance 114.2+j800 ohm referred to the high voltage side. Take the rated voltage as the base voltage and the rated VA as the based voltampere value.
Reduce the block diagrams below to find the equivalent transfer function a. (Case a only) First find unity feedback form, then find the equivalent overall transfer function
A 60 hertz, 3 phase transmission line has a toal seriesimpedance (Z) of (0.2 + j0.8) ohms per mile per phase and shunt admittance(Y) of (j5.31 E-6) mhos per mile per phase.It delivers 40MW at 220Kv ,with 90% poer factor lagging.
If the resistance of dry skin is 5 k? and accidental contact is made with a conductor that is at a voltage of 120 V, how much current can flow through the human conducting path. If contact with this same conductor is maintained for 10 s
The problem has two parts(a and b) and it asks: Find the power and rms value of each of the following signals: a) x(t) = 5 + Ccos(ωot+θ) b) x(t) = 2+7cos(1/2t+θ1)+3cos(2/3t+θ2)+5cos(6t+θ3)
Steam enters an adiabatic nozzle at 3.5Mpa and 300C with a low velocity and leaves at 1.6Mpa and 250C at a rate of 0.4kg/s. If the surrounding is 10 at 100Kpa and 18C, find A) The exit velocity B)The 2Nd law efficiency
A) the required step-up voltage ratio for satisfactory performance. B) the voltage ratio of a standard buck-boost transformer that most closely meets the requirements of the load. C) the voltage at the load with the buck-boost transformer installed.
The resistance of the coil is .4 ohm. The inductance of the coil is 2.4e-4 H. The rotor inertia is 2.0e-5 kg m2. The current to torque gain is 0.06 Nm/A. The friction torque is 0.18 Nm. A 12 V voltage source is applied to the motor.
Voltage regulator utilizes a 500 mW Zener diode with Vz=6.7V at 20mA, rz=lOohm and IzK=5mA. The supply voltage y+ has a nominal value of 12V but can vary by ± 1 V. The load resistor is fixed at 330ohm
question 1-a p-well is to be formed for a cmos process. the n-type substrate has a doping level of 2times?10?15
Create a state transition diagram for a simple state machine to detect a positive pulse. You choose either a Moore or Mealy machine. Write a Verilog HDL module for your state machine.
AnNMOS operating in triode region with Vds=0.1V conducts 60μA forVgs=2V. The device conducts 160μA for Vgs=4V. Calculate Vt. IfKn'=25μA/V2 , what is the device W/L What current would flow for Vgs=3V and Vds=0.15V
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd