What is the frequency of the signal

Assignment Help Mechanical Engineering
Reference no: EM131037004

Problem 1

Consider the cantilever beam shown below. Suppose the uncertainties in the material properties and dimensions are: wE = 2% wr =0.0005 in, wQ = 5 lbm/ft2, and wL = 0.01 in.

1093_figure.jpg

The natural frequency of the cantilever beam is given by

ωn = 11/rL2√(EI/ρΠ)

Calculate the resulting uncertainty in ωn al L =1.0 and L =4.0 in.

Problem 2
Suppose you are asked to sample the output voltage signal below from an analog sensor using a data acquisition system. Given the signal, complete/solve the following steps:

a) Graphically convert this signal from analog form(shown below) to digital form on the same plot assuming 3 bits of resolution. How many discrete voltage steps are there and what is the voltage step/size resolution?

b) What is the frequency of the signal? In order to properly sample and reproduce the characterstics of the signal in digital form, what should be the minimum sampling frequency and what is the theorm that governs this rule?

945_figure1.jpg

Problem 3

A platinum resistance thermometer is placed in a duct to measure the temprature of an airflow stream. The termometer is paced inide a cylindrical shell 6 mm in diameter (d) which has a polished outside surface with ε = 0.08 ± 0.02. The airstream velocity, U is known to be 3 m/s and the pressure is 1.0 atm. The thermometer indicates a temperature of 115oc. The duct wall temperature is measured at 193o C.

Calculate the true air temperature and estimate the uncertainty in this temperature. Assume that the uncertainty in the convection heat- transfer coefficient given below is ±15 percent. Also, assume that the uncertainty in the resistance thermometer measurement is ±0.3 C. The Prandtl number, Pr is 0.68 and the kinematic viscosity, v is 27.06 x 10-6 m2/s.

Reference no: EM131037004

Questions Cloud

Check your solution by a direct differentiation with time : For an interval of motion the drum of radius b turns clockwise at a constant rate in radians per second and causes the carriage P to move to the right as the unwound length of the connecting cable is shortened.
Real impact-meaning-resonance : Does Art Matter? Does it have any real impact, meaning, resonance, or any affect in your life, or anyone's - back to the beginning of humanity?
Question regarding the inventory control models : Discuss the importance of inventory control with respect to supply and demand. What benefit can tools such as ABC analysis and just-in-time controls provide for an organization?
Question regarding the forecasting : Discuss the different types of forecasts to include time-series, causal, and qualitative models. When might a researcher or project manager utilize exponential smoothing? What benefit does a Delphi technique provide when working with qualitative-base..
What is the frequency of the signal : Calculate the resulting uncertainty in ωn al L =1.0 and L =4.0 in - What is the frequency of the signal? In order to properly sample and reproduce the characterstics of the signal in digital form, what should be the minimum sampling frequency and w..
What velocity will the officer observe : Car A is moving with constant speed v on the straight and level highway
Evolving in healthcare operations management : What are some of the key trends that are evolving in healthcare operations management? How are systems and technology streamlining the operations within the departments that are support services? How is healthcare reform impacting the operations m..
What is the cost of the stock in the riskless portfolio : What is the cost of the stock in the riskless portfolio? What is the present value in the riskless portfolio? What is the value of the firm's call option? What assumptions in this analysis might not hold in the real world?
Problem regarding the economic profit : At the end of the first year of operating her new business, Mary's accountant reported an accounting profit of $150,000. What was Mary's economic profit?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Find the percent of volume change after a cube specimen is

if an isotropic material has a poissonamp39s ratio v. find the percent of volume change after a cube specimen is

  Steam at 10 mpa and 450 degrees c enters an adiabatic

steam at 10 mpa and 450 degrees c enters an adiabatic turbine at 80 ms and exits at 10 kpa 92 quality and 50 ms. the

  The energy loss in the system is 25 times the velocity head

the pump is delivering hydraulic oil with a specific gravity of 0.85 at a rate of 20 gallons per minute. the pressure

  A 1000w iron is left on the ironing board with its base

a 1000w iron is left on the ironing board with its base exposed to air at 20degrees c. if the surface temperature is

  The inlet and outlet diametersof the nozzle are20 mm and10

superheated steam enters a nozzleat 0.13 mpaand 600 k and exits at 0.1 mpa. heat interactions and frictional effects

  Balanced reaction equation

Butane (C4H10) burns completely with 160% of theoretical air at 208C, 1 atm, and 90% relative humidity. Determine (a) the balanced reaction equation.

  Determine the ratio of gross thrusts contribution to engine

the hot gas supply to a propulsion nozzle is at a pressure of 55 kpa and a temperature of 800 k. the ambient pressure

  What is the velocity of the fluid in the small section

Fluid is flowing in the pipe has two areas. The velocity of the fluid flowing in the larger area is 4 ft/s. The radius of the larger area is 4 inches. The radius of the smaller section is 2 inches. What is the velocity of the fluid in the small secti..

  Determine the flowrate molh for each species in the reactor

the fresh feed to an ammonia production process contains nitrogen and 75 excess hydrogen in stoichiometric proportion

  Design a journal bearing for a centrifugal pump running

Design a journal bearing for a centrifugal pump running at 1440 r.p.m. The diameter of the journal is 100 mm and load on each bearing is 20 KN. The factor ZN/p may be taken as 28 for centrifugal pump bearings. The bearing is running at 70 degrees Cel..

  Model the context of a system

Explain why it is important to model the context of a system that is being developed. Give two examples of possible errors that could arise if software engineers do not understand the system context.

  The collector transfers heat by natural convection to the

a flat plate solar collector 6ft by 12ft is mounted on the roof of a house. the outer surface of the collector is at

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd