Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
An 80 kHz sinusoidal voltage has zero phase angle and a maximum amplitude of 25 mV. When this voltage is applied across the terminals of a capacitor, the resulting steady state - state current has a maximum amplitude of 628.32 microamps.
a) What is the frequency of the current in radians per second?
b) What is the phase angle of current?
c) What is the capacitive reactance of the capacitor?
d) What is the capacitance of the capacitor in microfarads?
e) What is the impedance of the capacitor?
Write a function called AnalyzeData. This function is passed a double array along with a parameter that indicates the number of elements in the array. It is also passed a double value.
A minimum solution requires six states. Design your circuit using NAND gates, NOR gates, and three D flip-flops. Any solution which is minimal for your state assignment and uses eight or fewer gates and inverters is acceptable. (Assign 000 to the ..
1. Given R = 50Kohm and C = 100nF what is the frequency of oscillation 2. Given a required frequency of oscillation of f = 10kHz and R = 8kohm, what should the value of C be Calculate the signal to noise ratio given RMS Noise Voltage = 20mV and RMS S..
I)Design a circuit that gives you the following relation between input and output Vout = 2.17Vin + 5 Here are the constraints you need to work with: 1) Only one power supply that gives ±12V is available 2) Available op-amps run on ±12V
A three-phase 45 MVA, 345/34.5 kV distribution transformer is used as a step-down transformer. Determine the phase VA, Voltage, Current ratings and turns ratios of the transformer if it is connected as follows (a) Wye -delta
design an 8-bit programmable microprocessor-compatible TIMER IC by doing the following steps: Specify, draw , and clearly label( the functional name), the complete set of 8-bit registers that will be needed in the TIMER.
A filter with a great deal of attenuation must be placed in an amplifier chain. Ignoring all considerations other than the desire to minimize noise figure, would it be preferable to put the filter before or after a low noise amplifier Why
Determine the response of the system when aunit step is applied at input.
Design a sequential circuit with input x and output Z. The circuit outputs 1 whenever the input "1100" arrives. For example, the following sequence Z is generated as a result of the following input x
If Vid is 20-mV peak-to-peak sine wave applied in a balanced manner but superimposed on Vcm = 0.5 V, what is the lowest value that Vdd must have to ensure saturation -mode for Q1 and Q2 at all times. Assume Vt = 0.5 V.
A company has 100 metal halides (400W each with 1.2 ballast factor) and four motors (each with 50 hp capacity, 95% efficiency, 100% load factor, and 80% power factor). The power factor for the combined load
Germanium is n-type doped at 5x1015 cm-3 at T=300 K. The dimensions of the Hall device are d=5x10-3 cm, W=2x10-2 cm, and L=10-1 cm. The current is Ix=250 A, the applied voltage is Vx=100 mV, and the magnetic flux density is Bz= 500
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd