What is the force p to keep the system in equilibrium

Assignment Help Mechanical Engineering
Reference no: EM13216778

block mass = 200 kg is sitting on a smooth surface
F1= 500 N
F2 = 650 N
F3 = 900 N
FP = concurrent at the center of the block
unit vectors are:
e1 = 2/3(((rad(3)/2)i) + (rad(3)/2)j + rad(3)/2k
e2 = rad(6)/3(rad(2)/2i - rad(2)/2j - rad(2)/2k
e3 = 2/3(1/2i + j + k)

What is the resultant R of the 3 external forces f1, F2, and F3,
What is the normal force N for any angle between 0 and 90
What is the force P to keep the system in equilibrium for the angles specified?

 

Reference no: EM13216778

Questions Cloud

Compute the steady-state creep rate : If it is known that the value of the stress exponent n for this alloy is 8.2, compute the steady-state creep rate at 1300 K and a stress level of 89 MPa.
Determine the absolute maximum bending stress in the beam : If the beam has square cross section of 9 in., on each side, determine the absolute maximum bending stress in the beam.
Explain what financial statement and line : What source would they get that money from to pay for campaign and where would campaign expenditures go on the pro-forma financial statements? What financial statement and line?
Earth"s orbital distance : The intensity of sunlight that reaches Jupiter (orbiting at about 5 AU) is approximately what fraction of that at Earth"s orbital distance?
What is the force p to keep the system in equilibrium : What is the force P to keep the system in equilibrium for the angles specified?
Determine the average shearing stress in the bolts : a beam consists of three planks connected as shown by 3/8 in diameter bolts spaced every 12in.along the longitudinal axis of the beam.knowing that the beam is subjected to a 2500lb vertical shear, determine the average shearing stress in the bolts..
Victim precipitation affected by crime prevention techniques : How can victim precipitation be affected by crime prevention techniques? Provide examples. Apply the idea of victim precipitation to the violent crimes selected or assigned to your team. From the Uniform Crime Reports (UCR), what are the latest repor..
Define expensive and adds little business value : Create a report detailing the business value gained by consolidating to a single website, along with your recommendation for consolidation. Be sure to include your website profitability analysis.
Is there any difference between the stresses : is there any difference between the stresses measured at the top of the beam and at the same location on the bottom of the beam?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the average luminous exitance

Determine the average luminous exitance of the opaque interior surfaces of the room - what is the reflected component at this point?

  Determine the speed at which it strikes the ground at b

the snowmobile is traveling at 10m/s when it leaves the embankment at A.determine the speed at which it strikes the ground at B and its maximum acceleration along the trajectory AB.

  Calculate the moments of inertia

Determine the coordinates x' and y' of the centroid C of the area shown in the figure and calculate the moments of inertia of the area shown, about ox and oy axes.

  Determine the maximum axial compressive force

A short 60-mm-diameter circular bar is made of a material for which the maximum safe compressive stress is 80 MPa and the maximum safe shearing stress is 30 MPa. Determine the maximum axial compressive force that can be safely applied.

  Applied loads and young''s modulus and poisson''s ratio

Applied Loads, Young's modulus, Poisson's ratio, The Young's modulus and the Poisson's ratio for copper are 124.8 GPa and 0.36 respectively. When a tensile load is applie to a 1.5cm diameter copper rod

  Compute the second specimen radius after deformation

compute the second specimen's radius after deformation.

  Determine the distance traveled

a truck travelling along a straight road at speed 20 km/hr increases its speed to 120 hr/hr in time 15 sec.If its acceleration is constant, determine the distance traveled.

  Determine the required thickness of the insulation

If the pipe is to be insulated with glass wool insulation (k=.05 W/m C) in order to decrease the temperature rise of water to .25 degrees C, determine the required thickness of the insulation.

  Calculate the force required to hold the gate closed

the gate in the is hinged at H.the gate is 2 m wide and normal to the palne of the diagram.calculate the force required to hold the gate closed.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Determine be naturak frequency of the system

A 0,5Kg mass attached linear spring suffress 01 N/m. Determine be naturak frequency of the system in hortz e reapert this calculation for a mass of 50Kg and a suffress of 10N/m and compare your result to that of part.

  How is the technology utilized effectively

How is the technology utilized effectively or ineffectively? What are some barriers to more effective usage, and what are some recommendations you would make to overcome these barriers?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd