User Account

All Pages

What is the fluid viscosity

Assignment Help Mechanical Engineering
Reference no: EM13718050

You are given a liquid and are asked to find its viscosity. Its density is known to be 0.97 g/cm^3. You place the fluid in an open vessel to which a 20 cm long vertical tube with an inside diamter of 2 mm, is attached to the bottom. When the depth of the liquid in the container is 6 cm, you find that it drains out through the at a rate of 2.5 cm^3/s. If the diameter of the open vessel is much laarger than that of the tube and friction loss from the vessel to the tube is negligible, what is the fluid viscosity?

Reference no: EM13718050

Questions Cloud

Determine the composition of the mixture at equilibrium : A mixture of 30% CO2, 60% CO and 10% H2 by volume is placed in a container and maintained at 4680 R and 1 atm. Determine the composition of the mixture at equilibrium.
What is the mass flow rate of the cooling water required : Steam enters the condenser (heat exchanger) of a steam power plant at 20kPa and a quality of 95% with a mass flow rate of 20,000kg/h. A nearby river is used as a source of cooling water where the water will circulate through the tubes within the cond..
What is the quality of the steam in its initial state : A saturated mixture of water at 1,100kPa is throttled (in a throttling process) to a temperature of 105 degrees C and a pressure of 100kPa. What is the quality of the steam in its initial state?
Signboard truss is designed to support a horizontal wind : The signboard truss is designed to support a horizontal wind load of 640 lb. If the resultant of this load passes though point C, calculate the forces in members BG and BF. The forces are positive if in tension, negative if in compression.
What is the fluid viscosity : You are given a liquid and are asked to find its viscosity. Its density is known to be 0.97 g/cm^3. You place the fluid in an open vessel to which a 20 cm long vertical tube with an inside diamter of 2 mm, is attached to the bottom. When the depth of..
Determine net work developed per cycle-thermal efficiency : 1 kg of a gas in a piston-cylinder assembly undergoes a Carnot power cycle for which the isothermal expansion occurs at 800 K. The change in specific entropy of the gas during the isothermal compression, which occurs at 400 K is -25 kJ/kg. K. Determi..
Decide to install a pitot tube on the bottom : In order to double check your speedometer on your boat you decide to install a pitot tube on the bottom. One tube protrudes straight downward, while the other tube has a 90 degree bend, pointing the tip into the direction of motion.
Identify the problem statement in the essay : What is the purpose of the essay? Is it stated clearly and identify the problem statement in the essay. Does the introduction and conclusion focus clearly on the problem statement?
Regulation of the audit profession : Regulation of the Audit Profession and reporting Financial Performance

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Water at 20 mpa and 60 degrees celcius enters a mixing

water at 20 mpa and 60 degrees celcius enters a mixing chamber at a rate of 280lbmmin where it is mixed steadily with

  Fluids mechanics fluid mechanics boundary layer

fluid mechanics boundary layer

  A lap joint needs to be designed using 20-mm diameter

a lap joint needs to be designed using 20-mm diameter bolts to carry a load of 120 kn on the connecting plates. if the

  Calculate the back pressure for each of these scenarios

Consider a C-D nozzle with a throat and exit diameter of 252 mm and 657 mm, respectively. The reservoir pressure and temperature is 10 atm and 1000 K, respectively. Calculate the back pressure (Pb) for each of these scenarios:

  Knowing that the tension in member b is 6kn and that the

two structural members b and c are bolted to the bracket a. knowing that the tension in member b is 6kn and that the

  Assuming ideal gas behavior for the air and neglecting

a rigid well-insulated tank with a volume of 3 fe contains air at p1 22 lbfin2 and t1 475 bullr. the air is stirred by

  Determine the speed at which it strikes the ground at b

the snowmobile is traveling at 10m/s when it leaves the embankment at A.determine the speed at which it strikes the ground at B and its maximum acceleration along the trajectory AB.

  At resonance the amplitude is measured to be 058 cm at 080

a spring-mass is excited by a force f0sinomegat. at resonance the amplitude is measured to be 0.58 cm. at 0.80 resonant

  Steady-state temperature distribution in a rod

Steady-state temperature distribution in a rod with heat generation can be represented by the following differential equation: d^2T/dx^2+[-0.1+0.25sin((pi*x)/5)]T=0 where x = distance along the rod [m] and T is the temperature [K]. Obtain a solution ..

  Draw the system with any indicated work and heat transfer

a rigid well-insulated tank contains 3 kg of a 2-phase liquid-vapor mixture of water initially at 200 kpa with a

  A particle m weighing 06 lb has slid down a curved track

a particle m weighing 0.6 lb has slid down a curved track and is currently at the bottom moving to the right with a

  If the critical resolved shear stress is 62 mpa 900 psi

consider a metal single crystal oriented such that the normal to the slip plane and the slip direction are at angles of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd