What is the flow rate that the pump delivers

Assignment Help Mechanical Engineering
Reference no: EM13701711

A 4 kW motor is driving an oil pump with an efficiency of 95% down a 10 mm diameter pipe. If the velocity of the fluid downs the pipe is 1.8 m/s,

1. What is the flow rate that the pump delivers?

2. What is the pressure that the pump can deliver?

3. If a 25 mm bore hydraulic cylinder is connected to the pipe, what would the forward stroke speed of the cylinder be?

4. The viscosity of the oil is v = 0.00001 m2/s. Is the flow in the pipe laminar or turbulent?

Reference no: EM13701711

Questions Cloud

Is the thermal diffusivity of the ceramic of the mug : You notice that the ceramic coffee mugs in the office get too hot to hold about 10 seconds after pouring in the hot coffee. The wall thickness of the cup is 2mm. What, approximately, is the thermal diffusivity of the ceramic of the mug? According to ..
Estimate the average wall temperature : The weather channel reports that it is a hot, muggy day with an air temperature of 90°F, a 10 mph breeze out of the south west, and bright sunshine with a solar insulation (i.e. the solar heat source) of 400 W/m2.
Dell computer trades at a market-to-book ratio : Dell Computer trades at a market-to-book ratio of 15.86. The industry M/B ratio is 9.5. Even though Dell's M/B ratio is high relative to the industry, this ratio may tell us nothing about whether Dell's stock will outperform or underperform i..
Firm needs to raise $20 million for a new project : Your firm needs to raise $20 million for a new project. You forecast that earnings per share next year will be $1.65 if the firm issues new equity, but $ 1.55 if the firm issues new debt. Therefore equity is a better source of financing?
What is the flow rate that the pump delivers : A 4 kW motor is driving an oil pump with an efficiency of 95% down a 10 mm diameter pipe. If the velocity of the fluid downs the pipe is 1.8 m/s, What is the flow rate that the pump delivers? What is the pressure that the pump can deliver?
Employer transferred her to another town : After her employer transferred her to another town, Rosemary put her house up for sale. After two years of internet listings, open houses, repairs and price cuts, a buy finally came along.
Calculate the rate of heat transfer from this plate : A thin flat plate 6in square with a surface temperature maintained at 250°F is tested for drag in a wind tunnel with an airspeed of 100ft/s. The air is at standard sea level pressure and 60°F and flows over the top and the bottom of the plate. This f..
The velocity at the nozzle exit : Air at 22 kPa, 220K and 250 m/s enters a turbojet engine in flight at an altitude of 10,000m. The diffusor slows the air down to a very low speed relative to its inlet. The pressure ratio across the compressor is 12. The turbine inlet temperature is ..
Electrical energy into mechanical work : If you knew how much voltage you would generate with a given device and you needed to convert that electrical energy into mechanical work, how would you go about doing that?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd