What is the factor of safety n against tearing

Assignment Help Mechanical Engineering
Reference no: EM131062178

An inflatable structure used by a traveling circus has the shape of a half-circular cylinder with closed ends (see figure). The fabric and plastic structure is inflated by a small blower and has a radius of 40 ft when fully inflated. A longitudinal seam runs the entire length of the "ridge" of the structure.

If the longitudinal seam along the ridge tears open when it is subjected to a tensile load of 540 pounds per inch of seam, what is the factor of safety n against tearing when the internal pressure is 0.5 psi and the structure is fully inflated?

90_c9e398a7-b843-4c4e-a1e7-a5eaf4ee1c6f.png

Reference no: EM131062178

Questions Cloud

Present evidence from the gopro case study : Whilst there is no mark allocation associated for the Executive Summary & Intro in this assignment (ie. we had a mark allocation for Assignment 1, to ensure students made an effort in preparing an Executive Summary & Intro...and doing well in that..
Comprehensive application of the elements of critical : This assignment requires a comprehensive application of the elements of critical reasoning that we are studying in this course. The main objective is for you to follow the systematic critical reasoning process to thoroughly document all relevant i..
How you use a computer application for accounting : How do you feel your comprehension of a manual system benefits how you use a computer application for accounting? What areas of knowledge have assisted you with setting up your company
What is the maximum data transfer rate : What is the storage capacity of the disk? What is the maximum data transfer rate (bytes/second)? What is the maximum rotational delay? What is the transfer time?
What is the factor of safety n against tearing : If the longitudinal seam along the ridge tears open when it is subjected to a tensile load of 540 pounds per inch of seam, what is the factor of safety n against tearing when the internal pressure is 0.5 psi and the structure is fully inflated?
Verb of the fourth amendment : The right of the people to be secure in their persons, houses, papers, and effects, against unreasonable searches and seizures, shall not be violated, and no Warrants shall issue, but upon probable cause, supported by Oath or affirmation, and part..
Discuss how risk might be dealt with peck model : Discuss how risk might be dealt with in levels 1, 2 and 3 of Peck's model of the supply chain
What is the axial stress in the wall of the tank : What is the axial stress in the wall of the tank due to the water pressure?
Credibility of a wikipedia article : How is the credibility of a Wikipedia article different from that of a published research paper? Which resource do you think is more reliable or more useful? Is it reasonable to quote a Wikipedia article in your research essay? If you consult Wiki..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the total mass in the tank at the initial and

the rigid tank illustrated in the figure has a volume of 0.06 m3 and initially contains a two-phase liquid-vapor

  The initial interference required to produce

A laminated steel (E=200 GPa and nu=0.3) cylinder consists of a jacket with an inside diameter of 250mm and an outside diameter of 300mm shrunk onto a tube with an inside diameter of 150mm. The initial shrinkage pressure is 28MPa.

  Determine the free convection heat transfer

The plate described in Problem 9.14 has been used in an  experiment  to  determine  the  free  convection  heat transfer  coefficient.  At  an  instant  of  time  when  the plate temperature was 127°C, the time rate of change of  this  temperature..

  Find the maximum temperature in the wire

A copper wire, 5 mm in diameter and 15 ft long, has a voltage drop of 0.6 volts. Find the maximum temperature in the wire if the ambient air temperature is 25°C and the heat transfer coefficient h is 5.7 Btu/hr · ft2 · F.

  You have a bevel gear and shaft and you have to find the

you have a bevel gear and shaft and you have to find the maximum load that can be applied on it. what type of

  Without producing extensive plastic deformation of the bar

A design engineer is considering a structural change that will increase the tensile load on this member. What is the maximum tensile load that can be permitted without producing extensive plastic deformation of the bar? Give your answers in both newt..

  953 1kg of a fluid is compressed according to a law pn 025

9.5.3 1kg of a fluid is compressed according to a law pn 0.25 where p is in bar and n is in m3kg. the final volume is

  Contained in a piston-cylinder device

The refrigerant R-410a is contained in a piston-cylinder device, as shown in the figure, where the volume is 13 L when the piston hits the stops. The initial state of the fluid is -30 °C, 150 kPa, with a volume of 10 L. The entire system is brought i..

  Determine the mass flow rate of steam

Steam enters a diffuser at and with a velocity of and exits as saturated vapor at 240 F and 100 ft/s. The exit area of the diffuser is 1 ft2. Determine the mass flow rate of steam and the rate of entropy generation.

  Two carts a and b are moving in a straight line with

two carts a and b are moving in a straight line with velocities v and 2v respectively. the length of each of the carts

  Determine the magnitude of the reaction force fa in the

to use the principle of superposition to determine the total deflection in a cylindrical rod due to a static loading.a

  The plate is 2m long and 2m wide the temperature of the air

air flows parallel to an isothermal 100c flat plate with a free stream velocity of 10ms and free stream temperature of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd