Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1.Assuming a density of 120/ft^3 for masonry brick work, determine the max height of a brick wall if the allowable compressive stress is limited to 150#/in^2 and the brick is
a) 4" wide
b) 6" wide.
2.At what air temperature will exhaled breath condense by self-nucleation? Assume that a saturation ratio of 4.3 is required.
3.What is the equilibrium droplet size at a relative humidity of 100% for a NaCl cubic crystal 0.077 micron on a side?
4.Design a hollow steel shaft with an inside diameter 1/3 that of the outside diameter. The shaft transmits 200 kW at a speed of 20 Hz. The allowable shearing stress is 55 MPa, and the allowable angle of twist is 1 degree per meter of length.
Select the lightest available W14 section for column tosupport the axial compression loads Pd=150k and Pl=200 k if KL =14ft and A572 grade 50 steel is used. Column is assumed to be inframe that is braced against side-sway
If a tractor with 23-hp, a max speed of 3.6 mph in 1st gear and an effieiciency of 92% is operated operated down a 4% slope and the rolling resistance is 80 lb/ton, what is the maximum external pull in each of the 4 gears.
A lake has a water level which is used to determine if watering restrictions need to be implemented for the neighboring city. Water levels are measured on a weekly basis, and restrictions are placed if the lake level drops below 1060 ft. Weekly water..
The testing machin that covers the right range of load is to be chosen. it is expected to load the material up to a strains of 3%. if th material must remain elastic over that range, what would be the maximum load
The outer surface of the tank is cooled by air at 300 K with a heat transfer coefficient of 100 W/m2K. Determine the maximum temperature in the tank. Take the thermal conductivity of the wastes as 2.0 W/mK.
Determine the mass flowrate through boiler needed to produce 5000KW of power.
A pipeline 1200ft long and 8in. in diameter hasat its inlet point 75ft of available hydraulic energy with respectto the reference level. The velocity in the pipe is 5fps; thepressure at its end is 12psi.
Ammonium (NH4+) is a weak acid with a pKa of 9.26. The dissociation is: NH+4 NH3 + H+. Calculate the mass of ammonium added to 1 L of water in order to obtain a pH of 4 at equilibrium.
The elevtion of M is 875 . a transit was set at point M and a leveling rod was held vertically at point N. the horizontal cross line of the telescope was inclined so the reading of the horizontal cross line
The flow of water over a weir, can be computed by Q=5.35LH^(3/2), where Q is the volume low rate of water in cubic feet per second, L is the length of weir in feet, and H is the height of water over the weir in feet.
The compound interest formula is F=P(1+i)n where F is the total amount due, P is the initial cost or amount of money, i is the interest rate, and n is the number of periods interest is computed. 1.A student purchases a $1400 laptop computer for sc..
The truck is driving onto the stationary barge at the speed of v1. The masses of the truck and the barge are m and M, respectively. The barge is free to move on the water and the water resistance is to be ignored.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd