What is the efficiency of the turbine-generator

Assignment Help Mechanical Engineering
Reference no: EM13212157

A small hydroelectric power plant produces electrical power at a rate of 30 kW. The plant utilizes a stream of water that drops 40 m from a lake to the turbine and flows at a rate of 100 kg/s. What is the efficiency of the turbine-generator?

Reference no: EM13212157

Questions Cloud

Calculate temperature at the start of combustion : engine B is supercharged with after cooling and has cylinder inlet condition of 80c and 130 k pa to avoid knock problem it is desirable to have the air-fuel temperature at the start of combustion in engine B to be the same as in engine A calculate..
What price should john set for a carwash : If John were to lower his price by $1, he would sell more carwashes, and still be able to charge a price above his marginal cost. Explain intuitively why it would not be profit-maximizing to do so. What price should John set for a carwash.
Determine the ration of the time taken of cutting : in a crank or slotted lever quick mechanism the distance between the fixed centre is 150 mm and driving crank is 75 mm. determine the ration of the time taken of cutting & return strake .
What is the expected annual cost savings in dollars : A 50 hp motor with an efficiency of 0.80 is to be replaced by a newer model motor with an efficiency of 0.90. The motor is expected to operate 3000 hours per year. The cost of electricity in our area is $0.06 per kWhr.
What is the efficiency of the turbine-generator : A small hydroelectric power plant produces electrical power at a rate of 30 kW. The plant utilizes a stream of water that drops 40 m from a lake to the turbine and flows at a rate of 100 kg/s. What is the efficiency of the turbine-generator?
What is the mass of the lead weight : What is the mass of the lead weight, if 100 J of heat is lost from the water after the weight falls a distance of 3 m.
What is the change of energy stored in the battery : A 12 Volt battery is charged by supplying 3 Amps over a period of 6 hours. What is the change of energy stored in the battery if the battery loses 400kJ of heat during charging.
Explain what is the heat of vaporization of the substance : A liquid substance has a vapor pressure of 450.0 mmHg at 262.0 degrees celsius and 760.0 mmHg at 325.0 celsius. a) what is the heat of vaporization of this substance? b) what is its normal boiling point?
Calculate marginal rate of technical substitution of labor : a. Graph the short run total product curves for each production function for 0  L  25 in the case where K is fixed at 4. b. Graph the marginal product of labor curves for each production function for 1  L  25. c. Do these production functions exh..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Explain specific load and heat generated per minute

Design Engineering: Find Specific Load and Heat Generated Per Minute, A load of 6400 Kg is carried by a journal rotating in a 270 mm bearing diameter and 400 mm long. Find the specific load on the bearing and the heat generated per minute in the b..

  Large stationary brayton cycly gas turbine power

Large stationary brayton cycly gas turbine power plant delivers a powr output of 100MW to an electric generator . Minimum temperature is 300K so T1= 300k max temp is 1600k

  Hydrostatic relation an empirical formula relating

Hydrostatic relation, An empirical formula relating pressure and density for seawater w/ temperature held constant is

  Determine the velocity va

The catapult is used to launch a ball such that it strikes the wall of the building at the maximum height of its trajectory. If it takes 1.5 s to travel from A to B, determine the velocity vA at which it was launched, the angle of release q, and t..

  What is the actual strain

You have a 120 Ω quarter bridge 2 wire set up with Sg=2.10 and an unknown lead wire resistance. A 59880Ω calibration resistor is switched in parallel to the gage only and a recording instrument is set to give a -100 mm deflection for this calibrat..

  Determine diameter of a circular rod of ductile material

determine diameter of a circular rod of ductile material with a fatigue strength ,e=280 Mpa. Add a tensile yield strength of 350 Mpa. The member is subjected to a varying axial load from 700 kN to -300kN. Assume Kt=1.8 and factor of safety=2.

  Theory and practice of the product

Derive at least four concept designs to satisfy the given specification. Use short written descriptions and simple sketches to illustrate your ideas

  Explain tensile force and corresponding normal stress

Determine the magnitude of tensile force and corresponding normal stress of a wire A 28-ft length of 0.25-in

  Pulley system and motor

The 50-lb load is hoisted by the pulley system and motor M. If the crate starts from rest and by constant acceleration attains a speed of 15 ft/s after rising s = 6 ft, determine the power that must be supplied to the motor at this instant.

  Explain volumetric flow rate

Air enters a 0.6 m diameter fan at 16 deg C, 101 kPa, and is discharged at 18 deg C, 105 kPa, with a volumetric flow rate of 0.35 m^3/s.

  Construct the homogeneous solution

Construct the homogeneous solution in terms of four constant that could be determined from initial conditions and show the equations of motion

  A turbine salesman makes the following claim for one

A turbine salesman makes the following claim for one of his products: Steam enters a steady-flow adiabatic turbine at 4 MPa, 600 °C with negligible velocity and exhausts at 200 kPa with a velocity of 180 m/s

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd