What is the diameter of the capillary tube assuming it has

Assignment Help Civil Engineering
Reference no: EM13564966

You are designing a new thermometer using Galinstan, an alloy of gallium, indium, and tin that is a liquid at normal living temperatures. The coefficcient of thermal expansion is 190*10^-6 (1/kelvin). The thermometer will contain four cubic centimeters of Galinstan, most of which is in the bulb or reservoir that is connected to a capillary tube up which the liquid moves as it expands. If your design specifications are to have a 2millimeter change in the position of the liquid in the capillary tube for each degree Fahrenheit change in temperature, what is the diameter of the capillary tube, assuming it has a circular cross section?

Reference no: EM13564966

Questions Cloud

Determine the initial temperature and total enthalpy in the : A 10 kg of refrigerant R-134a at 300 kPa fills rigid container whose volume is 14 L. The container is then heated until the pressure is 600 kPa.
What is the mean time between counts : Suppose the counts recorded by a Geiger counter follow a Poisson process with an average of three counts per minute.
Find the bottom width and the depth of water channel : The rate of flow through a trapezoidal open channel is 20 m^3/s and the mean velocity of flow is 1m/s . the side slope is 1:1 and the bed slope is 1 in 5000. Assume Chezy's constant C as 60, find the bottom width and the depth of water channel.
Determine the thickness of the oil film assuming a linear : A solid cube with a side length of 0.4 ft and a weight of 110 lb slides down a smooth surface that is inclined at 45 degrees to the horizontal. The block slides on a film of oil with a viscosity of 1.85 x 10-2 lb-s/ft2. If the velocity of the block i..
What is the diameter of the capillary tube assuming it has : You are designing a new thermometer using Galinstan, an alloy of gallium, indium, and tin that is a liquid at normal living temperatures. The coefficcient of thermal expansion is 190*10^-6 (1/kelvin).
What percentage of the time will the through lane adjacent : A traffic engineer is trying to design a left turn bay on an EB approach to an intersection. The signal timing for left turns will have 10 seconds of “left turn only” green time and 50 seconds of red time each signal cycle. The green time will be suf..
Estimate the evaportranspiration losses for the area : Adriana wishes to accumulate $2,020,000 in 35 years. If 35 end-of-year deposits are made into an account that pays interest at a rate of 7% compounded annually, what size deposit is required each year to meet Adriana's stated objective?
How many cubic meters of borrow pit material is needed : The water content at 95% compaction is 11% on the dry side and 12% on the wet side of the compaction curve. What is the minimum additional weight of water per unit volume to achieve 95% Proctor compaction?
What is the concentration of residual nh3 in the aqueous was : Waste dairy whey is used to grow Kluyveromyces fragilis yeast in a continuous culture system operated at 30C and 1 atm pressure. Medium containing 4% w/w lactose (C12H22O11) and 0.15% w/w NH3 flows into a specially designed aerated bioreactor at a ra..

Reviews

Write a Review

Civil Engineering Questions & Answers

  How many watts of power would it take to heat 1 l of water

How many watts of power would it take to heat 1 L of water(weighing 1.0 kg) by 10 degrees Celsius n 1.0 h Assume no heat losses occur, so all of the energy expneded goes into heating the water.

  What is the length of the line

A line  is measured with a 2-chain tape, and a suveyors arrows  are use to  mark the end of the tape lengths . the three tallies are recorde the rear tapeman has eight arrows

  At what equal height above shorline should target be located

A surveyor is going to take a 5.5 mile sight across a lake from the top of one tower to a target on the top of another tower. It is desired to keep the line of sight 6 ft above the lake surface.

  Calculate the total head the pump is pumping against

A pump has the following pump curve is pumping at a rate of 5000gpm. Calculate (a) the total head the pump is pumping against. (b) brake horsepower required to drive the pump.

  Determine by what percentage the space mean speed

If the Greenshields model describes the relationship between speed and density on the highway, the jam density of the highway is 112 veh/mi, and the mean free speed is 64.5 mph,

  What will be the uniform load so to get the maximum

If a W14x53 is 20 ft long (simply supported) and is loadeduniformly to its moment capacity what is the maximumdeflection? What will be the uniform load so to get the maximum deflection?

  Imaging you have to shoot a basketball ball

Part B (Assignment): by trial and error, find the angle that will give the minimum force F to make a basket (hint: try 52 degrees)The trajectory of the ball will make a basket when x = L and y = Hb

  Parallel tangents of a reversed curve

The perpendicular distance between two parallel tangents of a reversed curve is 20m. The azimuth of the back tangents of the curve is 270 00 and the azimuth of the common tangent is 310.

  Determine the rate of evaporation of water

Water is to be boiledat sea level in a 30 cm diameter stainless steel pan on top of a3-kW electric burner. If60% of the heat generated by the burner is transferred to thewater during boiling, determinethe rate of evaporation of water.

  Determine the capitalized cost of the project to construct

This project is expected to have a first cost of $2,000,000 and an annual maintenance cost of $50,000. In addition, major repairs costing $250,000 will be required after 25 years and each 15 years thereafter.

  Determine the change in its length and the change in its

The acrylic plastic rod is 200mm long and 15mm in diameter. If an axial load of 300N is applied to it, determine the change in its length and the change in its diameter. Ep = 2.70 GPa, Vp = 0.4.

  Calculate the velocity in the constriction and the flowrate

Water flows through a 75 mm constriction in a horizontal 150 mm pipe. If the pressure in the 150 mm section is 345 kPa and that in the constriction 207 kPa, calculate the velocity in the constriction and the flowrate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd