What is the diameter of the bubble before it reaches

Assignment Help Civil Engineering
Reference no: EM13535622

1.Listed on cramster as ask. There is a car driving through water. Velocity is 12mph. Find h (max water depth) that will alow car to pass. List all assumption and calculations is the problem statement.

2.An air bubble of .3 inch diameter is released from the regulator of a scuba diver 100ft below the waters surface. The water temp is 85 degree's F.

What is the diameter of the bubble before it reaches the waters surface.

3.Estimate the discharge in a rock-bedded stream (d84=30cm) that has an average depth of 2.21m, a slope of 0.0037, and a width of 48m. Assume ks=d84.

Reference no: EM13535622

Questions Cloud

What are alternative treatment option for the removal of edc : What are alternative treatment options for the removal of EDCs in tertiary treatment? Be sure to justify any alternative treatment method you propose.
A water pump can generate a pressure diference : A water pump can generate a pressure diference ΔP (psi) given by ΔP=145-0.1Q2, Q is the flow rate in ft3/s. It suplies a pipe of diameter 20", roughness of .5 inches and length of 2500 ft.
Determine the net power delivered and the cycle efficiency : Determine the net power delivered and the cycle efficiency. What is the percent increase in the efficiency compared to an otherwise identical system with no regeneration. Assume “cold air-standard cycle” for both systems above.
What are the heat addition rate in the combuster and the : A “Cold Air-Standard Brayton cycle” gas-turbine power plant delivers a net power output of 60 MW to an electric generator. The compressor intake temperature is 300 K and the maximum temperature in the cycle is 1200 K.
What is the diameter of the bubble before it reaches : Listed on cramster as ask. There is a car driving through water. Velocity is 12mph. Find h (max water depth) that will alow car to pass. List all assumption and calculations is the problem statement.
Calculate the minimum required cross-sectional area : The moduli of elasticity of plain concrete and steal are 25 GPa and 207GPa respectively, and the corss-sectionial area of steel is 2% of that of the reinforced concrete.
Calculate the detention time in hours horizontal velocity : Two rectangular clarifiers(sedimentation basins), each 30 ft long, 15 ft wide, and 10ft deep, settle a combinedtotal of 0.40 mgd following alum coagulation. The effluent channelshave a total weir length of 60ft in each basin
The angle theta which the 6-lb. uniform rod makes with the v : A 5-lb force is applied to the center of the roller at A, causing the assembly to roll. If the roller has negligible mass, determine (a) the angle theta which the 6-lb. uniform rod makes with the vertical during the roll, and
Select the beam dimensions and reinforcement for a balanced : A rectangular concrete beam has f'c=3000 psi and steel with fy=40ksi. Select the beam dimensions and reinforcement for a balanced section if the beam sustains a moment as a result of dead load of 60 kip-ft and a moment as a result of live load of 90 ..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the carsvelocity and position when t

A car starts from rest and moves along straight line with anacceleration of a = (3s-1/3)m/s2, where s is in meters. Determine the car'svelocity and position when t = 6s

  Determine the power input to drive the compressor

Air enters an adiabatic compressor at 100 kPa and 17 degrees C at a rate of 2.4 m^3/s. It exits at 257 Degrees (C). The compressor has an isentropic efficiency of 84%. Neglecting the changes in kinetic and potential energy

  Find equilibrium flows and travel time before reconstruction

The routes are currently in user equilibrium. A reconstruction project on route 1 reduces capacity to 3.0 kvph, but total travel demand is unaffected. Field studies note a 35.28 sec increase in average travel time

  What sample size would be necessary to detect a true mean

Benzene is a toxic chemical used in the manufacturing of mechanical chemicals. A manufacturer claims that its exit (effluent) water meets the federal regulation standards with a mean of less than 7980 ppm of benzene.

  What is station and elevation of the lowest point on curve

An equal tangent vertical curve conects an initial grade of -3% and a final grade of +1% and is designed for 60mi/h. The PVI is at station 250+50 and elevation 732 ft. What is the station and elevation of the lowest point on the curve

  What is the outlet concentration after the treatment

A completely mixed retention basin is used to treat an industrial waste water consisting of a non-conservative pollutant, using a reaction that destroys the pollutant according to first-order reaction kinetics, with k = 0.216/day.

  Determine the minimum do concentration in the stream

A municipal WWTP discharges 22.5 MGD of secondary effluent containing 45 mg/L of ultimate BOD at 26.7 C with 1.3 mg/L of dissovled oxygen. The stream flow is 237 ft^3/s at an average velocity of 2.1 ft/s and an average depth of 7ft.

  Determine the maximum force the hand can apply

assume that the whole twisting moment is taken by the bone. If the humerus can withstand a shear stress Tmax=70.0 MPa, determine the maximum force the hand can apply without fracturing the humerus. The length of the forearm is 360 mm.

  Calculate the molar mass of the biomolecule

A 2.50-g sample of a large biomolecule was dissolved in 13.0 g of carbon tetrachloride. The boiling point of this solution was determined to be 77.85°C. Calculate the molar mass of the biomolecule.

  What will be the approximate amount of the quarterly payment

What annual investment is required at 8% per year compounded annually to accumulate to $100,000 at the end of 20 years?

  Determine the values for the energy grade line

4. Determine the values for the Energy Grade Line and the Hydraulic Grade Line for the tank and pipe system of problem 3. Plot the EGL and HGL.

  How to design the curve of the roadway at station

An equal tangent vertical curve is to be constructed between grades of -3.0% (initial) and 1.0% (final). The PVI is at station 110+00 and elevation 420 ft. Due to a street crossing the roadway, the elevation of the roadway at station 112+00 must b..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd