What is the desirable average velocity

Assignment Help Mechanical Engineering
Reference no: EM131270991

The Froude number for an open channel flow of velocity U and a depth of h was defined in Chapter 5 as

376_a0fb8452-db3d-4236-b29a-f04acd8d1f67.png

(a) Calculate the value of the Froude number for a 1-m-deep channel in which the water is flowing at an average speed of 0.5 m/s.

(b) The channel shape was tested in a 1/10-scale model. What is the desirable average velocity in order to keep the same Froude number (and not change the surface-wave behavior)?

Reference no: EM131270991

Questions Cloud

Sales promotions advertising decision sequence model : Explain why you agree or disagree with the contention that the APIC-type model is useful as a framework for direct marketers or sales promoters to operate within.
Presentation explaining government intervention : Create a 16 slides PowerPoint presentation explaining government intervention on Low income rent controls and housing vouchers. The presentation should include a detailed speaker notes or voiceover including the following;
Prepare brief description of two procedures : My assignment is: Prepare a brief description of two procedures that prevent or block mistakes in the hospitality service process. These appllications are commonly referred to as 'poke yokes' - roughly translated from Japanese into English as 'error ..
Treasury of a recently independent country : You are appointed secretary of the treasury of a recently independent country called Rugaria. The currency of Rugaria is the lav. The new nation began fiscal operations this year, and the budget situation is that the government will spend 10 milli..
What is the desirable average velocity : The channel shape was tested in a 1/10-scale model. What is the desirable average velocity in order to keep the same Froude number (and not change the surface-wave behavior)?
Persuade the state agency of the need for funding : Food bank is open four days a week. One director and four volunteers. Food bank feeds 100–150 families per week. Of those families, 95% have children under 18. Often, food will run out by the end of Thursday. With a small group, create three data dis..
Thinking about opening a hardware store : Your aunt is thinking about opening a hardware store. She estimates that it would cost $500,000 per year to rent the location and buy the stock. In addition, she would have to quit her $50,000 per month job as a sales clerk. If your aunt thinks sh..
Demonstrate their comprehension of the course material : Mini-Papers are single page reflections on a question or exercise. The paper is an opportunity for the student to demonstrate their comprehension of the course material and to apply it to the situation presented. The paper is also an opportunity f..
Identify overall scope and analysis of unexpected results : Using the results of your work from week two project Identify Overall Scope/ Analysis of Unexpected Results; two additional events will be introduced. You will again analyze the impact of these events to the final project

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Lbm block is pushed down a frictionless incline with a force

A 10 lbm block is pushed down a frictionless incline with a force of 5 lbf. the incline is 30 degrees relative to the horizontal. if the block starts from rest, what is its speed after it has been pushed 12 ft. Assume that gravity is 32.0 ft/ sec^2

  Calculate the bending stress

Consider a T shaped wooden beam comprised of a 2 x 6 and a 2 x 8 20 feet long. [Use nominal dimensions for beam cross section.] A steel plate 20 feet long and of cross section 6 x ½ inches is fastened to the top of the T. Calculate the bending stress..

  What is the temperature cm from the base

What is the temperature 7 cm from the base if the rod is made of a) pure zinc b) lead c) pure gold. Which will be the hottest at this point?

  Determine graphically the magnitude and direction of the

two structural members b and c are bolted to a bracket a. knowing that both members are in tension and that p 6 kips

  Determine the directions of the principal planes

At a given section a shaft is subjected to a bending stress of 20 MN/m2 and a shear stress of 40 MN/m2. Determine: the directions of the principal planes

  10 kg of water in a piston cylinder exists as a saturated

10 kg of water in a piston cylinder exists as a saturated mixture at 120 kpa with quality 40. the water is now heated

  Draw a schematic diagram for the autofocusing control system

Draw a schematic diagram for the autofocusing control system and explain the function of each component in the control system, including the encoder.

  Determine the thermal efficiency and the mep

compare it with efficiency of an otto cycle operating with the same maximum pressure?

  How to find y parameters in the s-domain

Using Fig. 19.80, design a problem to help other students better understand how to find y parameters in the s-domain.

  An aircraft flying at 10000 feet uses a pitot-static tube

an aircraft flying at 10000 feet uses a pitot-static tube to measure speed. the instrumentation on the aircraft

  Determine the flow rates for product and water that will

a countercurrent heat exchanger is being used to heat a liquid food from 15 to 17 c . the heat exchanger has a 23mm

  A nozzle with inlet area of 800 cm2 and inlet steam

a nozzle with inlet area of 800 cm2 and inlet steam velocity is 10ms. the steam pressure is 800kpa and temperature is

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd