What is the deflection of the manometer

Assignment Help Civil Engineering
Reference no: EM13550418

1.A grain-size analysis for a uniform sand in a loose state indicated that the soil particle diameter corresponding to 10% passing on the grain-size distribution curve is 0.18 mm. Estimate the coefficient of permeability.

2.A clean glass capillary tube having a diameter of .008 in. was inserted into water with a surface tension of 0.00504 lb/ft. Calculate the height of the capillary rise in the tube.

3.An Air manometer is connected to each side of an orifice, with a diameter of 8 inches, in a pipe with a diamter of 12 inches. If a maximum flow rate is 5 ft^3/s, what is the deflection of the manometer? The viscosity of the water is 0.000674 lbm/ft*s, and its denisty is 62.3 lbm/ft^3.

Reference no: EM13550418

Questions Cloud

Determine the carburizing time necessary to achieve a carbon : Determine the carburizing time necessary to achieve a carbon concentration of 0.35 wt% at a position 2 mm into an iron–carbon alloy that initially contains 0.10 wt% C
How long will it take for the concentration to be one-quarte : A batch system is assumed to be first order. The initial concentration is 225 mg/L. If the reaction rate constant is 0.65 hr^-1, how long will it take for the concentration to be one-quarter the starting concentration?
Determine the reaction rate constant : A reaction in a batch system is assumed to be first order. Data listed below was collected. Determine the reaction rate constant.
Calculate the mass flux rate and the flow rate : During a drilling operation, the small robotic device is subjected to an (F =) 900 N force at point C as shown. (? = 25°.) Replace this force by an equivalent force-couple system at point O.
What is the deflection of the manometer : A grain-size analysis for a uniform sand in a loose state indicated that the soil particle diameter corresponding to 10% passing on the grain-size distribution curve is 0.18 mm. Estimate the coefficient of permeability.
Estimate the power in watts that can be produced : An Engineer is considering the development of a small wind turbine (D=1.25m) for home applications. The design wind speed is 15 mph at T=10C and p=0.9 bar. The efficiency of the turbine is n=20% meaning that 20% of the kinetic energy in the wind can ..
Determine the soils coefficient of permeability : A constant-head permeability test was conducted on a clean sand sample. The diameter and length of the test specimen were 10.0 and 12.0 respectively. The head difference between manometer levels was 4.9 cm during the test.
Determine the sequent depth : A real estate broker charges a fixed fee of $50 plus a 6% commission on the landowner's profit. If this is uniformly distributed between 0$ and 2000$, find the probability distribution of the brokers total fees.
The total dissolved inorganic carbon of a sample of ground : The total dissolved inorganic carbon (TIC) of a sample of groundwater is 8.33 mM. The temperature of the aquifer is 15C, the pH is 7.5, and the ionic strength is 0.05 M. What is the H2CO3, HCO3-, CO3 2-, and the partial pressure of CO2? [Use activity..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the volume of water infiltrated on the field

a 30-acre field received 4 inches of rain with 35% runoff.Determine the volume of water infiltrated on the field ( assume all the water that doesn't runoff infiltrates )

  Calculate what is the distance after adjusting for sag

a 200ft tape is hung in catenary. It is supported at the 80ft mark the tension is 20lbf and the weight of the tape is 3 lbf 5 0z. The measured distance is 187.01 what it the distance after adjusting for sag

  Calculate the hydraulic conductivity of this clay

A falling-head permeability test was carried out on a clay soil of diameter 100 mm and length 150 mm. In 4 minutes the head in the standpipe of diameter 5mm dropped from 680 to 350 mm. Calculate the hydraulic conductivity of this clay.

  Determine the required are of concrete for the thrust block

Given that the max shear strength of the the concrete shore is 10 kPa and the engineer requires a F.S. of 2.5, find the required are of concrete for the thrust block.

  Determine the seepage velocity-v through the sample

The cross-sectional area of the sample was 60 cm2 and its length was 150 mm. For 80 cm3/min steady-state flow rate, a total head difference of 8 cm was measured across two points separated by 10 cm along the axis of the sample.

  Determine whatpressure head is needed from the pump

A WTP Operator is trying to size a pump that takes water from a WTPholding tank and sends it to a house on a hill above theplant. The operator's goal is to have 60 psi of waterpressure entering the house. The operator knows that the head loss (major+..

  What is max volume of treated wastewater should put in water

incoming wastewater , with BOD5 equal to about 200mg/l is treated in well-run secondery treatment plant remove 90 percent of the BOD. you are to run five-day BOD test with a stander 300-ml bottle , using mixture of treated sewage and dilution wate..

  Determine what is the partial pressure of the dry air

If the barometer reads 102 kPa abs, what is the partial pressure of the dry air, and what is its specific weight. What is the specific weight of the atmosphere (air plus the water vapor present).

  Determine what is the average shear stress in the oil

Two parallel plates, one moving at 4m/s and the other fixed, are seperated by a 5mm thick layer of oil of specific gravity 0.80 and kinematic viscocity 1.25 X 10^-4 m2/s.

  Calculate the density of air flow ate sections 1 and 2

Air flows steadily between two sections in a long, straight portion of 4 in. inside diameter pipe (D1=D2). The uniformly distributed temperature and pressure at each section are p1=100psia, p2=18.4psia, T1=540 R and T2=453 R.

  1 the us has produced the following quantity of gauges and

1. the u.s. has produced the following quantity of gauges and potatoes with the price of each listed in dollar

  Assume atmospheric pressure at the outlet section

The propellor is situated at the end of the tunnel wherethe area is 10 m2 (rigth before the tunnelis opened to the atmosphere). So I used the energyequation, but I have two unknows: pressure P of thetest section, and the shaft work hT orhP (I am not ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd