What is the cycle efficiency if a cold-air-standard

Assignment Help Mechanical Engineering
Reference no: EM13614304

A two-cylinder 250 cm^3 displacement motorcycle engine that operates on an ideal Otto cycle at 4500 RPM. The compression ratio is 9. Air enters the engine at 100 kPA, 27 degree C and peak temperature is 2250 degree K. Determine:

a. the net work percylinder

b. the cycle thermal efficiency

c. the net power output

d. what is the cycle efficiency if a cold-air-standard analysis is used with the following values: R = 8.314 kJ/kmol-K, cp = 1007 j/kg-K, cv = 0.720 kj/kg-K?

Reference no: EM13614304

Questions Cloud

Compare the minimum theoretical rate and the actual rate at : at steady state. a power cycle generates 100 mw of electricity while discharging energy by heat transfer at a rate of
On july 1 2005 kitel inc issued 9 bonds in the face : 1. on july 1 2005 kitel inc. issued 9 bonds in the face amountof 5000000 which mature on july 1 2015. the bonds were
Assuming that motorola follows a continuous review policy : motorola obtains cell phones from its contract manufacturer located in china to serve u.s. market. the u.s. is served
Our company has two checking accounts back in 2007 former : our company has two checking accounts. back in 2007 former bookkeeper by mistake entered wire transfer from one
What is the cycle efficiency if a cold-air-standard : a two-cylinder 250 cm3 displacement motorcycle engine that operates on an ideal otto cycle at 4500 rpm. the compression
Consider the electric circuit shown here consisting of a : consider the electric circuit shown here consisting of a 12.0-v battery and three capacitors connected partly in series
Zach received his amount of sharesthat were valued at 2970 : with their fence in place zack and clint set towork landscaping yards. since clint did the majority of the
At what speed must they pass through the furnace to be at : steel rods of 0.05m diameter are heat treated by being passed through a heat-treating furnace in which the atmosphere
A small plastic sphere with a charge of -70 nc is near : a small plastic sphere with a charge of -7.0 nc is near another small plastic sphere with a charge of -12 nc. if the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd