What is the cycle efficiency given that the efficiency of

Assignment Help Mechanical Engineering
Reference no: EM13621324

In an air standard regenerative gas turbine cycle,the pressure ratio is 5.air enters the compressor at 1 bar ,300 k and leaves at 490 K.the maximum temperature in the cycle is 1000k. what is the cycle efficiency,given that the efficiency of the regenrator and the adiabatic efficiency of the turbine are each 80%assume for air ,the ratio of specific heats is 1.4.

Reference no: EM13621324

Questions Cloud

Assume that in orthagonal cutting the rake angle is 20 : assume that in orthagonal cutting the rake angle is 20 degrees and the friction angle is 35 degrees at the chip-tool
Suppose that the life span of a certain type of fan has an : suppose that the life span of a certain type of fan has an exponential distribution with a mean life span of 25000
If we reject the null hypothesis what can we conclude : if we reject the null hypothesis what can we conclude subject to the ? risk?null hypothesis is falsealternative
A pharmaceutical company receives large shipments of : a pharmaceutical company receives large shipments of ibuprofen tablets and uses this acceptance sampling plan randomly
What is the cycle efficiency given that the efficiency of : in an air standard regenerative gas turbine cyclethe pressure ratio is 5.air enters the compressor at 1 bar 300 k and
The television show pretty betty has been successful for : the television show pretty betty has been successful for many years. that show recently had a share of 16 meaning that
Assuming the population is roughly symmetric construct a 95 : consumption of alcoholic beverages by young women of drinking age has been increasing in the united kingdom the united
The coefficient of discharge is 10 calculate power in kw : if a water jet machining jet is issued through 0.3mm dia at pressure 400mpa density of water is 1000kgmm3.the
Is type of restaurant factor in overall customer : the consumer reports restaurant customer satisfaction survey is based upon 148599 visits to full servuce restaurant

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Question 1 entropya in a coal fired thermal power station

question 1 entropya in a coal fired thermal power station indicate where the exergy contained in the coal is destroyed.

  Therefore is constrained to move in a circular arc of

the particle a is mounted on a light rod pivoted at o and therefore is constrained to move in a circular arc of radius

  Determine the back work ratio and the thermal efficiency of

consider a gas-turbine cycle with two stages of compression and two stages of expansion. the pressure ratio across each

  If the plate moves through the mid plane between the

a thin plate moves between two parallel horizontal stationary flat plates at a constant velocity of 5 ms.the two

  Find the cartesian components of force p acting in the x y

find the cartesian components of force p acting in the x y and z directions given p20n alpha 134.5 deg beta 55.0 deg

  You are to supply a design for an engine room crane

You are to supply a design for an engine room crane which will provide maintenance support for the main engine. Your design should include the rails the crane will sit on.

  The gas undergoes complete combustion with 120 of the

a power generator burns natural gas consisting of 30 ethane 60 methane and the balance nitrogen. the gas undergoes

  It strikes the smooth ground at a distance of 20 ft away

a tennis ball is struck from a height of 7.5 ft. it strikes the smooth ground at a distance of 20 ft away and bounces

  Determine the scalar component of the moment

Determine the scalar component of the moment at point 0 about line OB and the reaction at 0 - average normal and shear stresses on plane BB.

  A stack gas flowing at 80 m3min at t 25 degree c and 1 atm

a stack gas flowing at 80 m3min at t 25 degree c and 1 atm contains approximately 75 n2 5 o2 8 h2o and 12 co2. a

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Find the volume rate of ?ow in ab

Find the volume rate of ?ow in AB, the velocity in BC, the velocity in CD and the diameter of CE.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd