What is the corresponding wall thickness of the container

Assignment Help Mechanical Engineering
Reference no: EM13708126

1. A parison is extruded from a die with outside diameter = 11.5 mm and inside diameter = 7.5 mm. The observed die swell is 1.25. The parison is used to blow mold a beverage container whose outside diameter = 112 mm (a standard size 2liter soda bottle). (a) What is the corresponding wall thickness of the container? (b) Obtain an empty 2liter plastic soda bottle and (carefully) cut it across the diameter. Using a micrometer, measure the wall thickness to compare with your answer in (a). Supplement to 13.23: (c) why would your measurement of the 2-liter bottle be “off” from your calculations? Be specific.

2. The bottom of a chair (where you sit, the ‘seat’) will be injection molded by itself in a mold. Assume the chair is a disk, 24 inches in diameter and 1/10 inch thick. If the injection pressure is 1600 psi, what is the minimum clamp tonnage you need for the injection molding machine? Give the answers in standard tons.

Reference no: EM13708126

Questions Cloud

How much heat will be transferred in this lenght of duct : Water flows through a duct of varying area. The difference in stagnation pressures between two sections is 4.5 x 10^5 N/M^2. If the water remains at a constant temp, how much heat will be transferred in this lenght of duct?
Determine the rates of heat and moisture removal from air : Air enters a window air conditioner at 1 atm, 32C, 70% relative humidity at a rate of 2 m^3/min, and it leaves as saturated air at 15C. Part of the moisture in the air that condenses during the process is also removed at 15C. Determine the rates of h..
Find the distance between the neutral axis and the centriod : A curved bar has a rectangular cross section with height h=(r_o)-(r_1)=50mm and width b=100mm. It's inner radius is 200mm. Find the distance between the neutral axis and the centriod.
Cantilevered beam with a rectangular cross section : A cantilevered beam with a rectangular cross section is loaded by a force perpendicular to the beam centerline at the free end. The cross section is 100mm high and 25 mm wide. The vertical load at the beam end is 40,000 N. Calculate how long the beam..
What is the corresponding wall thickness of the container : A parison is extruded from a die with outside diameter = 11.5 mm and inside diameter = 7.5 mm. The observed die swell is 1.25. The parison is used to blow mold a beverage container whose outside diameter = 112 mm (a standard size 2liter soda bottle)...
Plot the final temperature against the initial pressure : An insulated tank is divided into two parts by a partition. One part of the tank contains 2.5 kg of compressed liquid water at 60°C and 600 kPa while the other part is evacuated. The partition is now removed, and the water expands to fill the entire ..
The inner pipe of a double-pipe heat exchanger : The inner pipe of a double-pipe heat exchanger has an OD of 1.9 in. and contains 36 rectangular fins of the type shown in the sketch below. The fins are made of steel (k=34.9 Btu/h ? ft ? ?F) and are 0.5 in. high and 0.035-in. thick.
Plot the mass of ice against the initial temperature of ice : A 0.3-L glass of water at 20°C is to be cooled with ice to 5°C. The melting temperature and the heat of fusion of ice at atmospheric pressure are 0°C and 333.7 kJ/kg, respectively, and the density of water is 1 kg/L.
An insulated tank is divided into two parts by a partition : An insulated tank is divided into two parts by a partition. One part of the tank contains 2.5 kg of compressed liquid water at 60°C and 600 kPa while the other part is evacuated.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd