What is the corresponding amplitude of vsig and v0

Assignment Help Electrical Engineering
Reference no: EM13275301

An Emitter follower with a BJT biased at Ic = 1mA and having β = 100 is connected between a source with Rsig = 20kg and a load RL = 1kg.
a) find Rin, vb/vsig, and v0/vsig
b) If the signal amplitude across the base-emitter junction is to be limitd to mV, what is the corresponding amplitude of vsig and v0 ?
c) Find the open Circuit voltage gain Gv0 and the output resistance Rout. Use these values first to verity the value of Gv obtained with RL reduced to 500Ω

Reference no: EM13275301

Questions Cloud

Calculate the dollar value of australian consumer surplus : Calculate the dollar value of Australian consumer surplus and producer surplus. Price of TV???s Quantity Demanded Quantity Supplied $500 0 50 $400 10 40 $300 20 30 $200 30 20 $100 40 10 0 50 0
What is the base-emitter voltage of the latter transistor : In a particular technology, a small BJT operating at vBE = 28VT conducts a collector current of 100 µA. What is the corresponding saturation current. For a transistor in the same technology but with an emitter junction that is 32 times larger.
Explain pair of amino acid substitutions : You are performing site-directed mutagenesis to test predictions about which residues are essential for a protein's function. Which of each pair of amino acid substitutions listed below would you expect to disrupt protein function the most
Estrimate the acceleration of the system : A mass of 3kg, is sitting on a 34° incline and is connected by a massless string over a pulley in the shape of a hollow cylinder, estimate the acceleration of the system
What is the corresponding amplitude of vsig and v0 : An Emitter follower with a BJT biased at Ic = 1mA and having β = 100 is connected between a source with Rsig = 20kg and a load RL = 1kg. a) find Rin, vb/vsig, and v0/vsig. b) If the signal amplitude across the base-emitter junction is to be limitd t..
What is the resistance of the other : When connected in series to a 110-V line, two resistors use one-fourth the power that is used when they are connected in parallel. what is the resistance of the other
State the net ionic equation for any single reaction : A piece of solid Ni metal is put into an aqueous solution of HNO3. Write the net ionic equation for any single-replacement redox reaction. Include states and charges
What is the rotation speed of the disks in rpm : A given application is reading and writing 32KByte files on a disk that has a data transfer rate of 150MByte/s. Measurements have shown that this disk incurs an average seek time of 6.7 msec and needs an average of 11.08 msec to complete a read or..
Find the magnitude and direction of the force : Find the magnitude and direction of the force the cable exerts on the pin for the pulleys

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the highest frequency of the analog signal

The basic sampling rate for the compact disc (CD) recording industry has been set at 44.1 kHz. (a) Determine the highest frequency of the analog signal that could theoretically be reconstructed from this sampling rate.

  Processor development

Explain the process of processor development

  Why is balancing load important for synchronous alternator

Despite the advantages to the synchronous alternator there is a downside and this has to do with keeping the load balanced on such a machine. Why is balancing the load so important to the synchronous alternator?

  Find the magnetic flux density at the center of the triangle

A thin conducting wire of length 3w forms a planar equilateral triangle. A Direct current I flows in the wire. Find the magnetic flux density at the center of that triangle.

  How to evaluate power dissipated in the components

how to evaluate power dissipated in the components of an RLC series circuit by using matlab software?

  Calculate the powers p1 and p2 dissipated across r1 and r2

A battery E (e.m.f 12v and internal resistance 0.8 ohms) and a resistor R1 (10 ohms) are connected in series across two parallel resistors (R2 = 12 ohms, R3 = 18 ohms). i) Draw the circuit diagram, determine the battery terminal voltage.

  Design common drain amplifier that can couple signal source

A signal source produces a 4 volt peak-to-peak sinusoid and has a source resistance of 100 ohms. We wish to drive a grounded 10 ohm load to at least 2 volts peak-to-peak with this source. The load cannot tolerate DC. Your amplifier should not burn..

  Determine a minimal sop expression for f

Construct a truth table for a three variable function that includes minterms 1,4,6,7. Construct the corresponding K map and use it to find a minimal SOP expression for F.

  What is difference in angle between load voltage and current

a. A load consumes 150kW with a power factor pf = 0.7 (lagging). If the load current is 240A (RMS), find the load voltage. b. An industrial plant has an inductive load which consumes 10kW of power from a 220VRMS line.

  How magnetic resonance imaging scans from childhood

trace how the electrons and holes move through the device under the two different biasing conditions. Explain how these three devices work in terms ofIn a study conducted at the National Institute of Mental Health,

  Count number of even elements of array of n 16-bit elements

Write a program to count the number of even elements of an array of N 16-bit elements. The array is stored at memory locations starting from $900. Use assembler

  Find what is the clock period of the signal

the frequency of a signal is equal to the reciprocal of the signal's period (f=1/p). For a computer with a 2.4 ghz clock, what is the clock period

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd