User Account

All Pages

What is the composition of the alloy

Assignment Help Mechanical Engineering
Reference no: EM13275287

QUESTION 1

The hardenability curves for a number of steels are shown in the diagram below. Rank the steels in ascending order according to their hardenability. If the thermal properties of the steels are the same, i.e. the cooling curves (temperature versus time) at a certain distance from the quenching end are the same for all the steels, explain the difference in hardness at a distance of 30 mm from the quenched end between 5140 and 4340 by plotting schematically the C curves for each in the same continuous TTT (i.e. temperature-time-transformation) diagram and comparing the resulting microstructures.

1624_What is the composition of the alloy.png

QUESTION 2

A magnesium-lead (Mg-Pb) alloy is slowly cooled (i.e. under equilibrium conditions) from 700°C. It is found by analysis that the first solid phase to solidify contains 20 wt% Pb. This alloy is further cooled to mom temperature. Using the equilibrium Mg-Pb phase diagram below, answer the following questions.

(a) What is the composition of the alloy and what is the temperature at which the first solid phase solidifies? (Estimates rounding to convenient numbers are sufficient.)

(b) What is (are) the phase(s) present at room temperature and the mass fraction of each phase.

(c) Is there any eutectic structure present at room temperature? If so, what is the mass fraction of the eutectic structure? Is there any phase present at room temperature which is not the primary phase (the first solid phase that has solidified) and does not belong to the eutectic structure? If so, what is the mass fraction of this phase.

(d) Sketch the microstructure at room temperature.

136_What is the composition of the alloy1.png


Attachment:- Materials.pdf

Reference no: EM13275287

Questions Cloud

Compute z in decibels required to give pe for noncoherent : Compute z in decibels required to give PE = 10-7 for noncoherent, binary FSK and for DPSK. For the latter, carry out the computation for both the optimum and suboptimum detectors.
Find the speed of the anther sac as it relases itspollen : The bunchberry flower has the fastest moving parts ever seenin a plant. Initially the stamens are held by the petals in abent position storing elastic energy liked a coiled spring. find the speed of the anther sac as it relases itspollen
Find the total bandwidth required for wireless system : Find the signal-interference ratio in dB when 120-sectoring antenna is used and the propagation coefficient n =3. If a cluster is replicated 10 times within the system, find the total number of users that can be served with this wireless cellular sy..
Explain the side chains of asparagine and glutamine : The side chains of asparagine and glutamine can undergo hydrolysis in aqueous acid. Draw the reactants and products for the deamination reaction. Name the products.
What is the composition of the alloy : What is the composition of the alloy and what is the temperature at which the first solid phase solidifies? (Estimates rounding to convenient numbers are sufficient.)
What will be the discount amount and net amount paid : What will be the discount amount and net amount paid if payment is made 26th July 2012?
Estimate the tension in the rope : A small object with a mass of m = 808 g is whirled at the end of a rope in a vertical circle with a radius of r = 128 cm. determine the tension in the rope
Define and write a net ionic equation for the reaction : Write a net ionic equation for the reaction that occurs when excess hydrobromic acid (aq) and iron(II) sulfide (s) are combined. Include states
Draw an asm chart for a computer that has three instructions : Draw a block diagram for a datapath that contains: an 8-word, three-port register file; an ALU that accepts operands either from the datapath or from an external source; and a shifter that shifts the A operand from the register file before it goes..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Explain the steam from the nozzles of a single wheel impulse

The steam from the nozzles of a single wheel impulse turbine discharges with a velocity of 600 m/s at an angle of 20 degrees. The blade wheel rotates at 3000 rev/min and the mean blade radius is 590 mm

  Compute the atomic packing factor

The unit cell for uranium has orthorhombic symmetry with a, b and c lattice parameters of 0.286, 0.587, 0.495 nm, respectively. If its density, atomic weight, and atomic radius are 19.05 g/cm3, 238.03 g/mol, and 0.1385 nm, respectively, compute th..

  Calculate the velocity and acceleration of collar a

In the position shown, the angular velocity and the angular acceleration of the rod AB are 4 rad/sec and 6 rad/sec2, respectively, both counterclockwise. For this instant calculate the velocity and acceleration of collar A. ( AB = 600 mm)

  Determine the acceleration of the car

Motor M draws in the cable with an acceleration of 4 ft/s2, measured relative to the 200-lb mine car. Determine the acceleration of the car and the tension in the cable. Neglect the mass of the pulleys.

  Examine deflection of an i-beam under a point load

The purpose of this project is to introduce you to the application of FEA by using the ANSYS software to examine the deflection of an I-beam under a point load.

  Derive the dynamic equation for rp manipulation

Derive the dynamic equation for RP manipulation of example 6.5 (Introduction to robotics by Craig)by using newton-euler's dyanamics.

  Determine the number of revolutions

Determine the number of revolutions that the motor executes in a) reaching its rated speed, b) coasting to rest.

  What is the eccentricity

A satellite is in Earth with an altitude at perigee of 550 km and an altitude at apogee of 5000 km.

  What is the average friction factor in the duct

Air enters an adiabatic duct of L/D = 40 at V1 = 170 m/s and T1 = 300 K. The flow at the exit is choked. What is the average friction factor in the duct?

  Draw and label a process flowchart

Propane gas enters a continuous adiabatic heat exchanger' at 40°C and 250 kPa and exits at 240°C superheated steam at 300°C and 5.0 bar enters the exchanger flowing counter currently to the propane and exits as a saturated liquid at the same press..

  Applied loads and young''s modulus and poisson''s ratio

Applied Loads, Young's modulus, Poisson's ratio, The Young's modulus and the Poisson's ratio for copper are 124.8 GPa and 0.36 respectively. When a tensile load is applie to a 1.5cm diameter copper rod

  Explain working with boiler suspension bolts

Working with boiler suspension bolts. An HRT boiler is 4766mm long and 3533mm in diameter. It has 66 steel tubes with a diameter of 9mm. The total dry weight of the boiler is 2.565 tonnes

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd