What is the channel response

Assignment Help Electrical Engineering
Reference no: EM13275775

Let the original symbol duration T be 0.1msec and the number of subcarrier is 16 (k=0:15). G d time TG for cyclic prefix is 0.02msec. The combined symbol period Ts becomes 0.12msec. Let the OFDM signal go through a time varying channel with the following 2-path model:

H(f, t) = ∑ an e-j2Π(ftΠ - fΠt) with N=2, an=1 for n=1,2, t1=0, t2=0.01msec, f1=20Hz and f2=-20Hz

a. What is the channel response Hk for subcarrier k=15 (i.e., 16th sub carrier) for t=Omsec:0.02msec:0.12msec (i.e., in a duration of a transmitted OFDM symbol (with cyclic prefix)?

b. If you assume the channel response H15 is constant in a symbol period (0.12msec), what is maximum variation (difference) of H15?

What is the maximum variation of Ho? What is the maximum variation of H8?

c. Assume channel response is constant in a symbol period, ,fed), Hk(t|n+1)=Hk(0.06msec+n*0.12msec) for (n+1)*0.12msec>t>n*0.12 m sec during the (n+1)th sym1:61 period, If you know, Hk(n) for n=1,3,5,...,11. you use these information to estimate Hk(n) for n=2,4,6,8,10 with a linear approximation. What are the estimation errors?

d. If you know, Hk(n) for n=1, 11, 21, ...,101, )(oboe these information to estimate Hk(n) for n=1,2,...,100 with a linear approximation. What are the estimation errors? (if you cannot program, find the errors for n=6, 16, 26, ...96)

Reference no: EM13275775

Questions Cloud

What is the size of the force required to lift the box : A box is lifted with a pry bar , by slipping the bar under the box and lifting up on the bar. what is the size of the force required to lift the box
What resistive force dose the air exert on her body : The downward acceleration of a 74-kg stuntwoman near the end of a fall from a very high building is 5.5m/s2
What fraction of the copper electrons have been removed : A 45.0 g ball of copper has a net charge of 2.1 µC. What fraction of the copper's electrons have been removed
Calculate the torque rating and the power rating : A long shunt cumulative compound motor is run at full load. It is rated 240 V, 10 A, 1200 rev/min. If Rf=180 ?, Ra=2 ?, Rs=1.22 ?, and the stray power losses are 160 W, find: a. The back EMF. b. The power rating.
What is the channel response : What is the channel response Hk for subcarrier k=15 (i.e., 16th sub carrier) for t=Omsec:0.02msec:0.12msec (i.e., in a duration of a transmitted OFDM symbol (with cyclic prefix)?
Explain what mass of nano3 and nanh2 must be used : NaNO3(s) + NaNH2(s) yields NaN3(s) + NaOH(s) + NH3(g) What mass of NANO3 and NANH2 must be used to prepare 15.0 g of sodium azide, assuming that the reaction runs with an 82.1% yield
What is the weight of the vehicle : A ford focus has a wheelbase of 274cm. Upon weighing, it is found that the front wheels have a weight of 7000 N, What is the weight of the vehicle
What is the speed of the car just as it passes the train : A train is moving parallel and adjacent to a highway with a constant speed of 33 m/s. What is the speed of the car just as it passes the train
Evaluate the uncertainty in the volume of titrant delivered : compute the uncertainty in the volume of titrant delivered. Report your result as the relative standard deviation in parts per thousand, to the nearest 0.1 ppt.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine equivalent circuits per phase as wye connected

Current, voltage, and power to a three phase system are measured and found to be 20 A, 550 V and 10.5kW respectively. Determine equivalent circuits per phase as follows: (a)wye connected series combination of resistance and reactance in each phase.

  What overall voltage gain results as measured from source

A 10-mV signal source having an internal resistance of 200 kO is connected to an amplifier for which the input resistance is 20 kO, the  open-circuit voltage gain is 2000 V/V, and the output resistance is 1 kO. The amplifier is connected in turn t..

  Determine what is the net electric field at location

A small object with charge Q1=6nC is located at the origin. A second small object with charge Q2=-5nC is located at m. What is the net electric field at location A m due to Q1 and Q2

  Write the code for the delay procedure

We would like to monitor the first two least significant bits of PORTB (use masking technique). Whenever both of these bits are set, switch all LEDs of Port A on for one second. Assume that the name of the delay subroutine is DELAY.

  What is numeric gain at high-pass filters cutoff frequency

1)A passive high-pass filter is built from a 100 kohm resistor and a 100 nF capacitor. what is its cutoff frequency 2)For the filter in the above question what is its numeric gain at its cutoff frequency

  Design a parallel set of lights when resistance of each bulb

The heavy duty battery can provide 9A for 4 hours period of operation each night. Design a parallel set of lights (select the maximum number of lights) when the resistance of each bulb is 12

  What electrical parameter does an ohmmeter measure

WHAT ELECTRICAL PARAMETER DOES AN OHMMETER MEASURE AND WHAT ARE ITS UNITS. SHOW BOTH NAME AND SYMBOL FOR THE PARAMETER AND ITS UNITS.

  How to use vhdl test bench to simulate all the three models

Use Modelsim and a VHDL test bench to simulate all the three models for a 4-to-1 multiplexer. Use basic gates for structural modeling. A tar VHDL library file is given for assistance.

  Calculate the instantaneous power absorbed by the resistor

A voltage v(t) = 359.3 cos(wt) is applied to a load consisting of a 10 resistor in parallel with a capacitive reactance XC = 25. Calculate The instantaneous power absorbed by the resistor The instantaneous power absorbed by the capacitor

  Write an instruction sequence to configure the sci subsystem

Write an instruction sequence to configure the SCI subsystem for operation with the following parameters: 1500 baud using a 9 MHz Bus Clock, 1 start bit, 9 data bits, 1 stop bit, no loop back, no idle line use, no wakeup, enabled receive and trans..

  What mah capacity should the batteries have

A student project is required to be portable and hand held. It requires 6 V DC power at a current of 150 mA. The batteries for the power supply must last for a minimum of 7 hours of continuous operation.

  What is the capacitance of the capacitor in microfarads

An 80KHz sinusoidal voltage has zero phase angle and a maximum amplitude of 20 mV. When this voltage is applied across the terminals of a capacitor, the resulting steady state current has a maximum amplitude of 0.7 mA.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd